Your cart is empty.
Your cart is empty.Product Description
BUILT IN IC DRIVER
The built-in intelligent IC driver provides better current stability and heat dissipation, extending the life of the 1156 LED bulb to 50,000 hours.
HIGH QUALITY 2835 CHIPS
The newly upgraded LED beads are a further leap forward in terms of brightness and area, providing you with a brighter view.
Universal 1156 or p21w Socket
Plug and play. Non-Polarity design. Simply plug the bulb in and you are all set.
clayton brunson
September 3, 2025
Work great for my 1997k2500. Had a bulb burned out and the circuit board looked like it had gotten hot. These work fine and no more rapid blinking with replacing the lights and relay with LED relay that was $8.
Yosan González
July 12, 2025
Muy buen producto, pensé que me llegaban 2 bombilla, pero vienen 4, lo recomiendo 100 por ciento
Antonio Lopez
June 16, 2025
Some car and some positions cannot use led directly, and will have error code
Gramps
April 22, 2025
I love it
Mike McCracken
April 21, 2025
Replaced my (40 year old) turn signal bulbs with these. Far brighter, and much more visible.
Customer
April 17, 2025
Experienced hyper flash also fried My control module which also controls wipers, wipers no longer work. Amazon could not help except with a $25 courtesy gift card. Reached out to seller no response yet.
Alan J. Lehman
March 31, 2025
The amperage of these lights are different then the original halogen lights and so the computer thinks the lights are out and still blinks fast as a warning signal. This can be fixed with specialized equipment. Do yourself a favor and just buy the original halogen bulbs.
dallin
March 24, 2025
Buy this if you like very bright led lights and have a suzuki carry db51t, fits da51t and db51t great value and worts great.
Celebrate
January 22, 2025
Replaced brake light on my Santa Fe Sport 2016, no issues
Claude Pepin
December 30, 2024
Ces ampoules sont parfaite mais c'est ma moto qui ne les adore pas car c'est comme si le système électronique est fait pour un globe normal et ne voit pas le DEL donc, j'ai pu juste en mettre 2 sur 4 sinon, il pense que mes globes sont brulés.
Smudge
December 20, 2024
Bright bulbs, well made but unfortunately even with the canbus adapter they still throw up an error
Theman & GF
December 15, 2024
These are a decent upgrade to the regular filament bulbs. They are red in both “taillight†and “brake light†mode. They took about 60mA low(tail), 300mA high(brake) (0.06, 0.3A) to power, which seems efficient to me. Testing them with a variable power supply they worked down to 6V, but below 9V they lost brightness. I could power them up to 24V, however I did notice some heat. They didn’t have any flicker/strobing when viewed with a super slow motion camera. All in all, they seem like good value. I’m assuming they will last as long or longer than a regular bulb.One thing to mention is they are (if you get the red ones), red in both taillight and brake light mode, which may not be proper for some vehicle that use them for a signal light. Trailers tend to use red for signalling, so that is why I’d recommend them for that purpose. Also they take a low wattage and that can cause flashers in the older cars to flash really fast due to the capacitor/resistor relationship in the flasher. For a trailer, usually your vehicle has figured that flashing speed out. In newer cars this can read as a bad bulb as it thinks it isn’t pulling enough current, so the bulb must be burnt out. In all but the fanciest vehicles I wouldn’t expect the computer to notice the trailer light “loadâ€.
Blackrain
November 24, 2024
Incredibly bright, solid fit. I don't know what else to say ither than these are a serious upgrade to standard bulbs and an inexpensive upgrade at that!Definitely recommended!
Recommended Products