Your cart is empty.
Your cart is empty.This quick disconnect seals up very well without a lot of work in connecting them.These feature a 1/2" Barb on the ends for easy connectivity to any 1/2" tubing you may have.Just get several silicone hoses of various lengths and put barbed male fittings on either end. Then use them wherever you need to in your system! They are so much easier to use than pushing and pulling the hoses off of barbs. It makes things interchangeable for cleaning, and provides quick installation and removal.
Rickey M. Horwitz
August 25, 2025
I use this for my brewing system. My LBS did not have the double camlocks type so I used these quick connects instead. The only drawback to this style of connector is that they might be a bit too hot to handle when your kettle boil is done. Obviously a rag or a mitt can be used to circumvent this.
Bradley Warbiany
August 23, 2025
For quite some time, I've had my inlet hoses for pumps attached to the pump inlet using 1/2" FPT hose barbs. I've never liked this setup, because the inlet hoses are always connected, even during storage. But when I set up the initial system, I was out of quick disconnects and just dealt with it.I finally pulled the trigger on these disconnects and after just one brew day, am VERY glad I made the switch. I was concerned that quick disconnects (as opposed to tri-clovers) may allow oxygen ingress and cause the pumps to lose prime. That concern was unwarranted, as the connection was solid and the pumps remained primed as expected throughout the entire brew day. And afterwards I was able to hang up my tubes so they can drain and air dry, as I've always wanted.The product itself is well-built and from everything that I can tell, high quality. They simply "feel" solidly constructed. And they work, so all is well. Highly recommended, especially for the price given that quick disconnects can often cost much more elsewhere.
Lepidolite Mica
August 10, 2025
You know how hard it is to find a quick disconnect for 1/4" threads? I was starting to think they just didn't exist, until Amazon decided to recommend home brewing instead of garden hoses. This was exactly what I was after for cleaning attachments, and with a bit of plumber's tape it seals plenty well enough.
JoeyTX
August 1, 2025
This is a fantastic way to update your brewing process. I just added a pump to my brewery and decided to add quick disconnects throughout. These are high quality disconnects. The only complaint would be that you have to put forward pressure to release the sleeve. That makes this a two hand operation if your pump isn’t secured to the bench or your mash tun is empty. Also make sure you buy some heat resistant gloves because these tend to get really hot in the process of transferring wort.
Eric
July 27, 2025
The only thing that is 1/2" is the male end inner diameter. Male end threads are 0.83-0.8" tapered major diameter and appears to be 14TPI making it a 1/2"-14 NPT thread. Female end barb is 0.33" inner diameter and 0.52" outer at the widest point and the depth of the barb is 0.98". Hopefully these measurements help the next person buying.
DMA
July 22, 2025
Solid, reliable product. Works with any brand receiver and creates a perfect seal for use with cold or hot liquids. I would recommend this product for anyone that uses quick-release components.
Lawrence Whitehead
May 31, 2025
Seems well made, works well. Not as heavy as some solid brass alternatives.
Raymond Boyle
May 29, 2025
I have purchased these quick disconnects before, this one is low quality. It does not go on or release. Sending it back. Very disappointed.
Rickey M. Horwitz
May 8, 2025
I use this for my brewing system. My LBS did not have the double camlocks type so I used these quick connects instead. The only drawback to this style of connector is that they might be a bit too hot to handle when your kettle boil is done. Obviously a rag or a mitt can be used to circumvent this.
Bradley Warbiany
April 21, 2025
For quite some time, I've had my inlet hoses for pumps attached to the pump inlet using 1/2" FPT hose barbs. I've never liked this setup, because the inlet hoses are always connected, even during storage. But when I set up the initial system, I was out of quick disconnects and just dealt with it.I finally pulled the trigger on these disconnects and after just one brew day, am VERY glad I made the switch. I was concerned that quick disconnects (as opposed to tri-clovers) may allow oxygen ingress and cause the pumps to lose prime. That concern was unwarranted, as the connection was solid and the pumps remained primed as expected throughout the entire brew day. And afterwards I was able to hang up my tubes so they can drain and air dry, as I've always wanted.The product itself is well-built and from everything that I can tell, high quality. They simply "feel" solidly constructed. And they work, so all is well. Highly recommended, especially for the price given that quick disconnects can often cost much more elsewhere.
Lepidolite Mica
March 12, 2025
You know how hard it is to find a quick disconnect for 1/4" threads? I was starting to think they just didn't exist, until Amazon decided to recommend home brewing instead of garden hoses. This was exactly what I was after for cleaning attachments, and with a bit of plumber's tape it seals plenty well enough.
JoeyTX
March 3, 2025
This is a fantastic way to update your brewing process. I just added a pump to my brewery and decided to add quick disconnects throughout. These are high quality disconnects. The only complaint would be that you have to put forward pressure to release the sleeve. That makes this a two hand operation if your pump isn’t secured to the bench or your mash tun is empty. Also make sure you buy some heat resistant gloves because these tend to get really hot in the process of transferring wort.
Eric
January 6, 2025
The only thing that is 1/2" is the male end inner diameter. Male end threads are 0.83-0.8" tapered major diameter and appears to be 14TPI making it a 1/2"-14 NPT thread. Female end barb is 0.33" inner diameter and 0.52" outer at the widest point and the depth of the barb is 0.98". Hopefully these measurements help the next person buying.
DMA
December 23, 2024
Solid, reliable product. Works with any brand receiver and creates a perfect seal for use with cold or hot liquids. I would recommend this product for anyone that uses quick-release components.
Lawrence Whitehead
December 21, 2024
Seems well made, works well. Not as heavy as some solid brass alternatives.
Raymond Boyle
December 10, 2024
I have purchased these quick disconnects before, this one is low quality. It does not go on or release. Sending it back. Very disappointed.
Recommended Products
$149.99
$ 69 .99 $69.99