Your cart is empty.
Your cart is empty.Product Description
2 Barrel Carburetor Carb 2100 2150 A800 Fits For Ford 289 302 351
- Carburetor fits for Jeep Wagoneer 1964~1978 Engine 360 Cu 5.9L
- Carburetor fits for Ford F100 1964~1978 Engine 289 Cu, 302 Cu, 351 Cu 4.7L 5.0L 5.8L
- Carburetor fits for Ford F250 1964~1978 Engine 289 Cu, 302 Cu, 351 Cu 4.7L 5.0L 5.8L
- Carburetor fits for Ford F350 1964~1979 Engine 289 Cu, 302 Cu, 351 Cu 4.7L 5.0L 5.8L
- Carburetor fits for Ford Mustang 1968~1973 Engine 289 Cu, 302 Cu, 351 Cu 4.7L 5.0L 5.8L
- Carburetor fits for Mercury Comet 1964~1982 Engine 289 Cu, 302 Cu, 351 Cu 4.7L 5.0L 5.8L
- Replace For OEM Part Number: 2100,A800
Replace OEM Part Number
2100 2150 A800
2 Barrel Carburetor Carb 2100 2150 Compatible with Ford 289 302 351 Cu Jeep Engine with Electric Choke.Replacement Heavy Duty Metal Construction.
Package Contents
- 1 x Carburetor
- 1x Grease Nipple
- 1 x Mounting Gasket
- 1 x Seal Ring
- 1 x Float Level Ruler
- Carburetor comes with Mounting gasket
Kind Note:
The cleaning of the carburetor should be carried out in a clean place. For the cleaning of internal parts, please use the special cleaner for carburetor or industrial gasoline. Please clean up the oil channels and air filters as well as use the clean fuel before installing the 2 Barrel Carburetor.
Main Specifications
- CFM：300
- PUMP JET:60
- MAIN JET: 122
- IDLE JET: 120/AIR JET: 120
- Venturi Size:1.16inch=29.5mm
- NEEDLE VALVE: 2.2 mm
- VENTURI(CHOKE TUBE):29.5
- AUXILIARY VENTURI : 13.5
Jack Lyons
2025-09-05 14:08:15
performing well, excellent quality for a reasonable price
Austin
2025-09-02 11:15:00
Definitely replace the throttle body with a rebuild kit before installation. Besides that, it's more than reliable than OEM!
Jason
2025-08-18 17:03:02
* Edit of initial review * After replacing the gasket for the power valve the carburetor is running great, I was pretty excited to get this on my Jeep as it was so cheap and most of the reviews were good, but that excitement was short lived. It ran well for about 5 minutes and then the pain started. First the fuel inlet clogged inside the carb. I took the top off, cleaned everything out and put it back together. It started and ran for about 30 seconds before the power valve started leaking all over the place. Replaced the power valve and gasket and runs correctly now. If you buy this plan on buying a full carb rebuild kit to go along with it. It is cheap for a reason.
Bug
2025-08-08 12:02:53
Fit perfectly. Easy to install. No leaking. Cars now runs perfect and I didn't even have to adjust it.
Robert Hosea
2025-08-03 18:44:27
I purchased this carburetor in January of 2024 and installed it on my 1983 F-150, which has a 351 Windsor motor in it. For the first two months of using the truck for plowing snow, the motor ran fine. After that though, the motor started to run very rough, and also very rich. Luckily though the snow plowing season was over and the truck was parked. The truck was used lightly over the Summer, but because it was still running very badly it pretty much just stayed parked. I recently started to work on the motor though, to figure out what was going on with it. I sure didn't think the problem could be the "new" carburetor, but I decided to remove it and tear it down anyway. What I found inside was a mess. The bottom of the fuel bowl area where the float and the needle & seat are, was covered with a layer of fine black "stuff". The black stuff was also inside the small port openings that are inside the fuel bowl area. Next, I removed the power valve and I found that the diaphragm in it had literally disintegrated, and that's what all of the black stuff was from. See attached picture. I thoroughly cleaned the carburetor, and then replaced the power valve with a used power valve from another 2150 style carburetor, and that fixed the problem. At least for now. I'm not going to use this carburetor though. I can't trust it. I will be removing this carburetor ASAP and replacing it with one from an entirely different company.
Geeky
2025-07-17 13:06:49
This thing bolted right up. Needed some adjusting of course, buy fixed our problem of not idling well right away. Great value!
Steven Mitchell
2025-05-27 12:04:52
Been on truck for a year,have a brand new Edelbrock sitting here but afraid to change it, can't believe it works so good
Jeff Burnham
2025-04-08 20:44:36
Works great! Perfect replacement.
Travis
2025-02-04 10:25:24
Had to modify choke to fit, basically had to remove choke assemble all together to fit to standard ford 2 barrel manifold
Recommended Products