Your cart is empty.
Your cart is empty. 2 Inch diameter Clear PVC pipe (Schedule 40), Cut to Length.
PVC pipe is measured by the nominal inside-diameter (ID), not the outside-diameter (OD).
Pipe has an approximate ID of 2.047 inch and an approximate OD of 2.375 inch, per PVC Schedule 40 Specifications. As with all extruded pipe, the inside diameter can vary a little. Tolerance for the inside diameter is +/- 2% of the stated diameter.
This pipe is manufactured in strict compliance to ASTM D1785.
Pipe has a bluish tint to prevent yellowing from UV light (as seen in pictures).
For use with standard PVC fittings and PVC cement.
This pipe should be protected from the sun. Extended exposure to ultraviolet light may cause discoloration and the heat may cause warping.
Length Tolerance: +/- 1/16 Inch
Please note that there is no product packaging with this product, it is just the pipe itself.
Pipe weight: 10.1 oz. per foot.
Do not use PVC pipe with compressed air or gases as it can cause the pipe to explode and create shrapnel.
Item quantity is 1 piece.
How to cut: If you need to cut the pipe, you should avoid using a ratchet-style PVC cutter, as that will likely break this pipe. Instead, use a saw such as a hacksaw, miter saw or radial arm saw, or one of the pipe cutters that you tighten a little, turn on the pipe, tighten some more and turn on the pipe and repeat until the pipe is cut.
Henry Chang
August 29, 2025
Great item.
Jimmy Stewart
August 27, 2025
This was used for a Rube Goldberg project where a 2" diameter tulip drill bit was mounted inside. A small ball then was dropped into the tube and the ball spiraled around the tulip drill like a screw. It served its purpose well.
James S. Cundiff
August 20, 2025
It would have been better if it were actually clear (without tint) but it is fine other than that.
James Dziadulewicz
August 13, 2025
When you need to confirm water is flowing this is the solution.
Jack Hubbard
August 6, 2025
Installed clear to know exactly where my fluid levels were in my tanks. Used a circular saw to cut with an old blade put on backwards. No splintering or cracking. Cut easily and cleanly. Install was straight forward and simple.
sb tech
June 13, 2025
A little pricey but should work.
Steven Robinson
May 26, 2025
Was exactly what I expected, had to sand the inside and outside edges of the ends as they ended up cutting the gaskets but otherwise perfect
WeGOThere
May 25, 2025
Used for laundry drain, now I can see when lint trap needs to be changed.
Henry Chang
April 22, 2025
Great item.
Jimmy Stewart
April 10, 2025
This was used for a Rube Goldberg project where a 2" diameter tulip drill bit was mounted inside. A small ball then was dropped into the tube and the ball spiraled around the tulip drill like a screw. It served its purpose well.
James S. Cundiff
April 5, 2025
It would have been better if it were actually clear (without tint) but it is fine other than that.
James Dziadulewicz
March 13, 2025
When you need to confirm water is flowing this is the solution.
Jack Hubbard
February 23, 2025
Installed clear to know exactly where my fluid levels were in my tanks. Used a circular saw to cut with an old blade put on backwards. No splintering or cracking. Cut easily and cleanly. Install was straight forward and simple.
sb tech
January 28, 2025
A little pricey but should work.
Steven Robinson
January 17, 2025
Was exactly what I expected, had to sand the inside and outside edges of the ends as they ended up cutting the gaskets but otherwise perfect
WeGOThere
December 29, 2024
Used for laundry drain, now I can see when lint trap needs to be changed.
Recommended Products
