Your cart is empty.
Your cart is empty. Widely use : Electric Radiator Fan plastic rods Installation Kit Compatible Mounting 7" 9" 10" 12" 14" 16" Electric Radiator Spal fan, Electric Cooling Fan and Transmission Cooler .
Easy to install：Clean the path with a cleaning brush first. Just use a soft touch and roll the posts back and forth for easy pass through the coil and radiator.slide the foam on the opposite side, and then push on the clip and you are done. It will find its path - do not push forcefully or it may damage the coil/radiator. No tools needed except some diagonal cutters to trim the excess.
Equipped with protective springs: The set contains 4 protective springs, which can prevent the bottom of the installation from breaking.
Sturdy and small enough：this mounting kit is strong easy flexible and easy to use! Great for applications where space is tight.
Package include: 12pcs nylon mounting rod, 24pcs foam pad, 12pcs spring, 12pcs fixed buckle.
Features:
Provides a strong, long lasting and installation-friendly design
Universal design for any car, truck or other automotive vehicle
Heat resistant components for long lasting durability
Compatible with radiators, oil coolers and transmission coolers
Material: Plastic+Metal
Package include:
12 x Mounting Straps/Ties
12 x Strap/Tie Locks
24 x Foam Pads
12 x Metal Tension Springs
Eddie Turbyfill
September 7, 2025
Makes easy work of installing electric fans on radiator.
sean conway
August 26, 2025
Works good
Ruben Duran Jr
August 16, 2025
I purchased these product because the fan unit that I purchased did not come with them works perfect and I have an extra set will buy again if needed.
Jared
August 7, 2025
Do not buy. I put my fan on crank my car up and they vibrated off the little plastic thing that tightens the zip tie up will not lock it will slide off. A waste of money.
Steve
August 6, 2025
The locking ties would not hold and vibrate loose, I had to glue them
Tandra hughes
July 6, 2025
Does the job perfectly.
CBJB
June 28, 2025
Got this for re-mounting a supplemental cooling fan on my Jeep. The straps seem to be holding well, have been in-place for several months now with now issues. Will update if they fail.
bumpit762
May 22, 2025
usally there flat so they slip between the find like a zip tie would. mounted them to a heat exchanger with normal fin density. they bent the fins and I couldn't fit it thru. I had to remove it and use a pick to open the fins up... not for someone looking to install them on the car. bench install only. maby for some radiators with a low fin count. the stoppers are large and take up room. one of the disc's didn't hold I had to pit 2 on one tie. would not get again. I could of done better with a washer and 2 zip ties nit to mention it wouldn't of damaged the fins!
Ùيصل الاØمدي
May 17, 2025
ممتاز واØسن من التولي٠والØديد
Old Bear
March 11, 2025
I’m glad I bought the extra sized kit as I wound up needing to replace my radiator about a week after I did the first install so I didn’t have to wait. Product works well and hold my oil cooler to my radiator.
Frank
March 2, 2025
Had them the very next day. Exactly as advertised. Same quality as original
Rob
February 25, 2025
They don’t hold any tension. Once you tighten them against the spring they pop off and loosen.
Ken S
February 12, 2025
had to pull a couple of the first attempts off and then they wouldn't hold as tight as the first time so I replaced them
Recommended Products
$51.00
$ 27 .99 $27.99
$28.99
$ 13 .99 $13.99
$69.99
$ 32 .99 $32.99