Your cart is empty.
Your cart is empty.Allstar Stainless Steel Brake Hose Kit for GM Metric Brake Vehicles features a brake hose kit that is stainless steel and fits big GM brake vehicles with 7/16-20 inches bolts. It is d.o.t. approved. The kit include two 16 inch stainless braided lines with banjo fittings attached. It also includes banjo bolts, crush washers, frame adapter fittings, frame tabs and holding clips..
michael schmidt
September 3, 2025
Very good quality and delivery time. They are going on the front Axle of a1932 ford roadster.
Kira
August 7, 2025
The big GM version was the one purchased. Used for disk brake conversion on a 67 Camaro. The caliper end bolted into the 69 nova calipers with no problem and the other end matched the threads on the 67 Camaro hard lines. Plenty of length between both mounting points. Looks very good. Will probably buy again.I installed by threading SS line connector to hard line, then hammering retaining clip in. Next the caliper hose end was installed. Then the hard line hose end was rotated to give the best line pathway between the two connection points before the hard line hose end was tightened up.
GS4
August 6, 2025
Had issues finding the right length with SAE threads. These fit great and no leaks
Joe
July 15, 2025
Hoses are of good quality, banjo bolts are not correct though.
Customer
July 9, 2025
Great brake lines, performance is great and same with the looks.
Speedwrench
May 26, 2025
Looks very clean and attractive with a Stainless Steel lines and fits perfect. I installed it on a Ford 9inch rearend that was shortened for a tubbed and narrowed 66 Nova, I would buy it again.
J. Zaharia
April 29, 2025
Bought these to use on a 53 Chevy Bel Air with Mustang II front end and GM Metric calipers. Just installed, no use yet, but length was great, installation easy, and quality seems to be quite good. I had no issues using these with the GM Metric/G-Body calipers. Great addition to 49-54 Chevy Car disc brake conversions. Worked with stock lines and hose bracket, but it was great that a set of brackets came with in case your application is slightly different. The only critique I may have is that the braided outer sheath does not have plastic/rubber coating like the Russel lines have. I would definitely use these again.
Mace
April 20, 2025
Looks like a nice kit for the money. Unfortunately, mine was mispackaged with 10mm banjo lines when it should have been 7/16. Can't use it so back they go... Also note the braided lines are bare, no outer shield, so the line can act like a saw if it's improperly installed and/or rubs against anything.
gordie french
April 7, 2025
very good seller and fast shipping
Dennis
March 7, 2025
perfect for my project
This was a beautiful picture to paint, I love it!
January 24, 2025
I used this on a 1979 Trans am , and it worked perfectly , a little longer than stock, which I wanted . These replaced Russel lines I feel the Russel lines are a little too short , and turning sharply puts a lot of stress on the lines.These lines were used with Wilwood dual piston front calipers , which required 7/16 “ banjo bolts . These lines work with these bolts …. They probably would work with earlier years 77’ and older.If you have 10 ml banjo bolts calipers on a 79’ - 81’ trans am , these lines won’t work.
Brandon Lobsinger
January 20, 2025
These all star ss flex lines part 42032 fit 79 Camaro perfectly
Gino...
January 15, 2025
This was exactly what I needed for my front disc brake conversion on my 1951 Mercury Monarch. Everything required is in this kit to replace the rubber brake lines, including the locking clips which are hard to find individually. Would definitely recommend!
Recommended Products
$20.38
$ 10 .99 $10.99