Your cart is empty.
Your cart is empty. ANCIRS 4 Pack 2mm Needle Test Probes, 600V/10A Non-Destructive Multimeter Test for Leads tl71 tl75
Features
This multimeter test probe is made of premium nickel plated copper material, very good sensitivity, accuracy and stable performance.
This test probes is suitable to be inserted into a 2mm connector, and the end connector can be inserted into a 4mm banana connector.
CAT II 600V/10A
fit for fluke multimeters and fluke test leads tl71 tl75
100% Customer Satisfaction
If you have anything concerned with the item, please first to choose contact us and we will take care of it for you.here is how Find your order in your amazon account, click the " contact seller" button beside the order ID.
wanda c leckey
2025-08-26 12:47:28
Great test probes at a good price. Prime shipping was prompt. Used probes right out of box.
Roy W. Perkins
2025-07-25 14:30:15
These multimeter extension adapter probes fit onto my existing probes , used a little piece of electrical tape to secure both adapters, just my preference. Other than that they worked great for the price!
Mark Clairmont
2025-06-03 18:01:58
Im able to easily check voltage on circuit boards and molex connections.
One Soldier
2025-05-30 12:45:45
I'm an HVAC technician and routinely need to break out the needle probes to check voltage via wire connections, which means swapping leads. Loved my Fieldpiece delux leads right up to the point where I lost one of the regular leads down a wall while in an attic. Had to get replacement leads since FP doesn't sell the rebuild by themselves. Got a basic set and then was stuck swapping the entire lead set every time I needed the needle leads... which was a huge pain and waste of time. Theme slip right on several types of "regular" leads (fluke, southwire,...). They hold well and their resistance is within an acceptable range (>.5)... after you clean them (some kind of protective coating?). They are super convenient... The negative: I grabbed the plastic cone and pulled it right off the needle along with the black needle insulator when I was taking it off. Those was after about a week or two of use. It went back together just fine, but now I pull them off by grabbing the tip. A little annoying, but hey two sets were $10! I can deal with that since they're otherwise so convenient.
R B
2025-05-23 17:40:02
Fit right on the end of the Kaiweets probes and are great for getting readings on smaller components without hitting other things on the PCB or slipping around. The tips are quite small and sharp. Recommend!
Cornytheclown
2025-05-21 18:25:48
They do what they are supposed to do. Hold up well.Would be nice if they came in a little hard plastic case.
Sylvester Williams
2025-04-19 17:49:25
Well I guess you get what you pay for. These were a good price, but the common side (the black one) didn’t fit tightly onto either of my set leads, the Pomona nor my Fluke
Joseph Price
2025-04-10 17:41:26
Great for circuit boards.
Andrew
2025-04-03 10:39:56
useful when troubleshooting shooting roof top units.
matthew l barclay
2025-03-20 19:37:54
Fit my fluke meter.
Nn
2025-03-03 11:45:57
Excelente costo beneficio
Jean-Michel
2025-02-18 10:03:42
Un peu plus gros que les Fluke mais tout de même pratique . Vont bien sur les tige fluke
Matt
2024-12-22 14:17:44
These are perfect to reach deep, annoying siemens auxiliaries to measure resistance. Fits really nice and snug on my fluke original test leads. I wish they were 1mm thicker, so be careful, they will bend easily, but for this specific testing it works great!
Recommended Products
$139.98
$ 60 .99 $60.99