FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I'd have to say that you'd need a very strong adhesive such as "Tite Bond" or similar (available at Menards for instance). Your typical liquid nails wouldn't do, as you need something strong enough that would quickly set and create a strong enough bond for the tiles not to fall off.CUTTING: With respect to cutting the tough PVC tiles, I found that cutting from the back-side using my Milwaukee Hackzhall (basically a powerful light-weight portable sawzhall that can easily be controlled one-handed) along with a special universal DIAMOND-BLADE, which can be purchased at your local hard-ware store, did the trick. This blade with diamond bits/chips on the edge, along with the hackzhall, cut through the PVC like sword through butter and allowed me to make some critical/difficult cuts. To further trim the PVC, I used very sharp/new shears to trim to size. Concerning cutting-out for the outlets, etc., I flip the tile and use a sharp razor, but be very careful as the PVC is slick and you could slip or accidentally make the wrong cut; so you could also use a touch metal ruler to prevent/minimize slips of the razor. In my case, I like to recycle stuff, so I used remnants of the metal security door/bar that came from the top of the metal gate that was not used as a hard metal ruler. Remember, easy does it and safety comes first...The application is not too bad on a very flush/leveled wall. If your wall has uneven areas, be prepared to have to use weights of sorts to lean against it. This will delay installation as you may have to do this for every few tiles, or for a trouble section. I have had to use ladders and scaffolding in order to apply heavy weighs such as cinder bricks, clay bricks, and actual weights such as dumbbells and barbells as high as 7-8 ft off the ground to hold the tiles down just long enough to cure (dangerous, so not recommended, but as a Construction Tech, I know my limits and I always have my hard hat on...).The end results are stunning... Especially if you take the time to CAULK between the seams (this is an important extra step that separates the PROS from the mediocre). This hides the seams a lot better and creates a nice continuous seamless brick wall, and makes it all look more realistic. I have gotten nothing but positive review/feedback from all who saw the brick wall.I also did the utility room with the water lines for the electric hot water tank, the furnace, etc.., in the same 3D wall tiles and it looks stunning... Yes, the utility room was a bit of an overkill as the mechanicals will fill-up this room eventually, so you would not see much of the 3D wall, maybe a third of the wall would show if that. However, I personally wanted a challenge, and I wanted a permanent solution to the utility room often needing to be repainted after a few years. This is a more permanent maintenance-free solution, just as with the bathroom, as the wall-to-wall and ceiling tiling (who does that lol?), would offer air-tight, water-proof, low maintenance, easy clean-up look for many years to come, thus saving $$$ in the long run. I am sold on this product and I also purchased their 3D back-splash and would be reviewing before and after on that too. That was also a hit. I will return to buy a ton as I am now focusing my life-long dream/goal of TLC of real estate properties.

An easy diy that will elevate your wall decore. There is a learning curve to install, but once you get the hang of it its easy enough. I stabilized the panels with double sided tape and then found itty bitty finishing nails to fasten them to the wall. I was able to align the edges close enough to make it look seamless and didn’t need caulk.

Looks amazing and super easy to put. Got it for my tv wall and it looks amazing

The media could not be loaded.

Beyond beautiful, follow directions, you only need glue on two sides which have more surface area, not the other two thin sides. Cutting is a bit of an hassle, but you can figure that out

These panels made a huge difference in this space. I get lots of compliments. It's plastic, but from a distance you can't tell. The hard plastic is very good quality. Pops off the like 3D. It's beautiful. I'm a little obsessed and want to add difference styles and color to other rooms. It's extremely easy to put up. In my opinion, it's better than wall paper. The only difficulty is cutting around the outlets. Worth the money and effort.

Horrible.. don’t buy! There is no edge on the sides for glue or tape to stick on. Tried three different ways to hang it. Nothing works.!!

This product was just OK. It was a little too bulky for my standard. It is very plastic looking maybe you would do good for a bigger project it was not OK for mine

facili da installare, dimensioni precise e veramente belli esteticamente

Tres beau, pas Cher et facile à installer. moi je l’ai installé avec tape 3M, très facile.

Amaaazing highly recommended

Excelente productos, estoy satisfecho, si compraría mas, me llego antes de lo prometido y sin ningún daño

I used these panels to put on top of an uneven wall in my residential trailer home. The walls are thin and as it's an old one ( the trailer) the walls are " wonky". So I needed a layer of insulation I'd bought previously and as I'm not the best diy'er it looked messy. Then I saw these wall panels, love the design,couldn't stick them on as they are partly hollowed out so not enough adherence space, so plan b, bought a staple gun and stapled them on. So far so good. Because of the optical illusion of the design I think I got away with the crap installation!!Good value, arrived quickly, well packed.