Your cart is empty.
Your cart is empty.Product Description
Breathe New Life Into Your Old, Dented and Rusted Baseboard Heaters With Our Simple, Easy-to-Install Baseboarders Basic Steel Covers
Amazingly Durable
Each Baseboarders Basic panel and accessory is made of hiqh quality steel, is professionally powder-coated and will not rust.
Designed with Safety In Mind
Single piece panel construction ensures proper airflow around the heating element while prohibiting direct access to it, making it safer for children and pets.
Easy Slip-on Installation
Installation is an easy DIY project, requiring no tools or hired help. Simply remove the existing baseboard heater endcaps and front cover panel, snap your new Baseboarders Endcaps onto your Baseboarders panel, position the Baseboarders assembly onto the original back plate & push down firmly into place, that's it — you're done!
Baseboarders Basic Provides a Clean and Minimalistic Aesthetic — the Most Cost-Effective Option
Baseboarders Basic...Designed for Form and Function
- 3', 4', 5' & 6' standard panel lengths (note: panels can be cut to custom lengths with tin snips)
- Made with high quality rust resistant galvanized steel
- Powder coated semi-gloss white finish
The Basic Series is the most cost effective option for those looking to keep project costs down. It is available in most common panel lengths, however has limited installation and accessory options. Baseboarders Basic provides a clean, minimalistic aesthetic at an increased value. Use multiple panels for longer lengths with a Coupler between. Panels can be cut for shorter lengths with tin snips.
Look For These Baseboarders Basic Accessories
- Basic Left Endcap (EC004-LF-WHT)
- Basic Right Endcap (EC004-RT-WHT)
- Basic Coupler (CP004-WHT)
- Basic Inside 90 Corner (IC004-WHT)
- Wall Brackets (WB001-WHT)
Note: Only Baseboarders brand Basic accessories fit Basic panels.
Retrofitting Guide to Ensure Proper Fit / Measuring for Length and Layout
STEP 1: Remove one endcap and the front panel. Measure between the floor and the top of the heater.
- Objective: 7.5" or greater
- If less than 7.5" use the Wall Brackets (WB001) for mounting. This will bring the height up by a minimum of 1.25".
STEP 2: Measure from the bottom of the heating element to the top of the heater.
- Objective: Between 5″ and 6.75″
- If less than 5″ use the Wall Brackets (WB001) for mounting. If the distance is greater than 6.75″, the Premium TALL profile should be used.
STEP 3: Measure from the outside face of the finned tube heating element to the back plate.
- Objective: Less than 3.25″
- If larger 4″ x 4″ or 4″ x 6″ commercial style element is in place, a wood molding will solve the depth issue.
STEP 4: Measure for length and layout
- There is no need for fractional or perfect measurements. Each endcap can offer up to 1.75" for a total of 3.5" when using an endcap at both ends of the panel.
- Standard straight lengths are measured from end to end using the original back plate. If a straight section is missing the back plate, measure from one extreme end of desired coverage to the other extreme end of coverage. Then subtract 1″. This is the ideal panel length.
- Baseboard heaters longer than 6′ will require the use of multiple panels and couplers to register the ends together. Example: 8′ = Two 4′ panels and a Baseboarders Basic Coupler to connect them.
- If Inside Corners are required, panel lengths can be determined by: a. Removing endcaps, b. Measuring side 1 from pipe to corner, c. Subtract 3'' for depth of the adjacent cover, d. Repeat with side 2.
Tom
2025-09-03 17:24:55
Very good manufacturing. Excellent paint. Sturdy. Installed in 2 minutes. A little expensive. Highly recommended.
david andrus
2025-07-28 14:37:24
They look good but expensive and easy to install. About $500-$600 for 1 room about 30 feet purchased ,including corner brackets,end brackets and joiner bracket
Mark H
2025-07-27 12:15:26
This baseboard cover is great product and such an upgrade over the terrible Slant/Fin covers that were there before. I actually bought one of those Slant/Fin replacement covers from Home Depot and was so turned off by the ugliness (even of a new one) and the complexity of installation with the whole housing that has to slip behind the heating unit, etc.. I decided to look around for an alternative and found these. These base boarders are SO easy to install, literally 2 brackets, I screw each (see picture). They seem very well made. Wish I could replace all the covers in my house!
Another Smith
2025-05-09 13:32:43
Originally this came severely damaged and the seller sent me a new one right away! It came two days later and was perfect.I really like the way it looks on my heater pipes. The old one I had had a bottom and this one does not, but the cover is longer I think it looks much better. I like that the vent holes are on the top and the side and my old one was not like that. So far, great product and super easy to install! I left the back of my old one and it slipped right on top. Took me five minutes to put in.
Bertha Moreno Labort
2025-04-03 15:15:29
The media could not be loaded.
Jm
2025-03-19 20:40:14
These could not be easier to install. They just slide right on and make my old baseboards look brand new! I just got two for a bedroom so I didn’t mind paying a little more but these would be really expensive to do a whole house. I also wish they were just tad bit longer as mine don’t go all the way to the floor. All in all I’m happy with them.
HR MICH
2025-03-06 11:49:03
Perfect fit and so easy to install! Looks and feels very strong and durable. Very happy with this product. HVAC service call and labor avoided!!
Frequent Shopper
2025-02-07 11:22:27
I bought one and was so pleased I came back for 2 more! They fit perfectly and look so attractive. They changed the whole look of the room. They are very well made and look much more expensive than some of the old baseboard heaters or even some of the new ones that they make today that are very tinny and cheap looking.
Recommended Products