Your cart is empty.
Your cart is empty.Product Description
Heavy-duty & multipurpose universal battery quick connector set from Driver Recovery Products. Provides simple and convenient method for connect/disconnect power to a winch or other electrical device such as remote battery chargers, power inverters, solar setups,trailers, or for any purpose requiring a high-current, quick-disconnect connector.
SPECIFICATIONS
- Color: Red
- Material: PC fire-retardant materials+stainless steel
- AMP Rating: AC/DC 175
- Gauge: 2-4 AWG
- Rated Voltage: UL rated at 600 volts DC or AC
- Medium Withstanding Voltage: 2200DC
- Contacts material: copper silver
- Fire rating: 94-V0
50AC 6-10 GAUGE
- Connector Dimension: 3-1/8"" x 2-1/8"" x 1""
- Terminal Pins Diameter: 0.5"
- Wire Size: 0.2" - 2.75"
- Connect/disconnect Cycles: 10,000 times
- Operating Temperature Range:-4°F-221°F / -20°C-105°C
- Suitable For: UPS battery power connector
- Vibration Resistance: Excellent
- Impact Resistance: High
How to Install
- Insert the wires into the terminal pins, then solder or crimp them.
- Insert the terminal pins into the connector housing and lock them in place
h82paint
2025-07-03 10:21:49
I am wiring up quick disconnects on a pair of 4x4 trucks. (Winches) I have giant gauge +- cable, and these terminate the ends perfectly. I've set it up where I can power the winch on either bumper, or leave the entire circuit disconnected near the battery. Quality seemed good, time will tell. People like the look of the setup, and functionally they work. 12000 # winch so draw was decent...through 2 sets of connectors to the rear.
Jake
2025-06-17 10:42:17
Worked great. Didn't have a crimping tool that could crimp this, ended up going to town on the terminals with a ball-ended hammer and wrapped real good with electrical tape.
Ricardo
2025-06-14 10:09:47
Excelente 👌
DDane
2025-05-26 13:09:51
Used to create a quick disconnect for my subwoofers box, installed on 10GA wire. Components were as described, assembled decent, the lip on the terminals is slightly too shallow, in my opinion, as I tested them disconnect after assembly and the second time I pulled them apart, one end dislodged from the retaining terminal. Took my grinder and gave the wire terminals a bit more of an edge, works perfect now. Would definitely purchase again.
Customer
2025-05-10 14:28:45
I used this to wire a large 12v air compressor into the bed of my truck so that it can easily be removed. It works great. I used 8 gauge wire and it fit great. Easy to install and great material that should last a long time.
Derf
2025-04-30 21:34:51
I looked for a long time to find sturdy heavy duty electrical connectors like these. I have a winch mounted on a trailer hitch slide in and used these so I could take the winch on and off the back receiver hitch. Ran heavy wire from battery in front to connector in back. Works flawlessly. Winch also fits on heavy duty car hauler for dual purpose.
perldrivr
2025-03-31 20:11:01
Item was a perfect fit with the plug on my manlift. had to build a powerpack for my Skyjack manlift, needed plug to match one on machine. I soldered cables into the contact prongs, then they just snapped into place in plastic plug housing, easy peasy!, perfect match for plug on machine, back in business!
BigSmiler
2025-01-10 17:10:47
These are two identical parts that fit together when assembled--BUT NOT until assembled--correctly. The silver pins have a tiny hook-like edge on one side of the tip. These have to fit against the copper plates inside the plastic case. Don't do this until you have your wire bonded to the pins because it's challenging to disconnect the pins from the copper. The copper is Not there for conducting electricity, but only as a spring clip to hold the silver pins in place. That worries me because if the connector should ever get hot from high current, copper loses its springiness easily. Steel would've been a better choice for a spring.
Anthony M.
2024-12-30 11:06:07
The lugs don’t sit as tight as the genuine Anderson plugs and push through then you connect them
TJ
2024-12-22 21:54:36
They are worth it.
B. Man.
2024-11-28 15:50:34
I used these to plug my Yamaha outboard into the battery charge system.They were easy to install and work well.
Lessard V.
2024-11-17 14:44:06
Ok
Billy Bass.
2024-11-15 14:25:41
Quality is just ok.
Recommended Products