Your cart is empty.
Your cart is empty.A smart add-on GPU brace to protect your graphics card and motherboard for longer period of use. The Cooler Master Elv8 helps reduce the Sag of heavier graphics cards and the stress on PCI-E slot on the motherboard. The length and height adjustments allows it to work with almost any graphics card. It also features a beautiful addressable RGB strip to enhance the light Sync with the entire system.
Heather T
2025-08-05 13:58:54
Another great Cooler Master product! I read a few other reviews where some people had issues with this bracket being flimsy, but I didn’t feel as this was the case, as mine felt pretty sturdy. One reviewer also mentioned that the screw holes were not really usable and they said they had to drill a little bit of extra room in order to get the bracket to sit right. I did not have this issue as the screw holes on mine had a little but of wiggle room for me to properly position the bracket.I have an Aorus RX 5700 XT, which is a huge GPU, and it sits perfectly level, I did not have to forcibly bend the product for it to sit right like a few other reviewers mentioned.My only complaint with the product is the cable that is supposed to plug into the motherboard. I tried looking for an answer for a while before I bought this product and couldn’t find any clear answer so I hope I can help someone with a similar situation. I have an Aorus Z390 Pro Wifi motherboard which does not have the Gigabyte proprietary 3 pin ARGB connector, but instead a standardized 3 pin ARGB connector. The included cables were long enough to reach the ARGB header located at the top right of the motherboard (I didn’t use the lower one because I would have to shove more cables behind the PSU shroud), however, the 3 pin ARGB connector that is supposed to work for the other brands of motherboards were extremely loose, so I could not plug this product directly into my motherboard.To solve this issue, I purchased an ARGB splitter cable and plugged it into my motherboard header, and directly plugged that into the cable for the bracket, completely leaving out the included cable that adapts to different motherboards. If you do this, I recommend using the included cable connection holder because for some reason, all the Cooler Master cable connectors just seem to be loose.**If your motherboard has a jumper for your ARGB header, make sure it is set to 5V and not 12V, or you will burn up this product.**All in all, great product, looks great, it syncs with Gigabyte’s RGB Fusion software, besides having to purchase a separate cable for my motherboard, no complaints, easy to install!
Roberto J.
2025-07-23 13:08:00
This is my first GPU holder however I am impressed. It does not sag and was easy to install, didn't need instructions however I did review them just to be sure. It is big enough to hide the eye sore of a wifi card underneath my GPU that wasn't matching my color scheme so that is a plus. The RGB works great and was immediately recognized however I can not seem to find any description of this product's number of led's which has a barely noticeable effect on certain RGB effects.Overall, I like and prefer the simplistic look and wish this came in white to better match my theme. Holds my GPU and produces no rattling noise that I thought would occur due to the uneven shape of my GPU.
xsbs
2025-07-10 10:46:31
Installation was a pain for me as my 3090 FTW3 doesn't have a flat fan shroud and is wavy. Unfortunately, the weight of the card is just a bit too much and is making the bracket sag. I'm talking less than 1 degree, but it's definitely not a perfect orthagonal 90. Good thing is that it does support the GPU from sagging any further, but like I said, it isn't an even 90. Kinda defeats the purpose of the bracket if it's not eliminating 100% of the sag, but it is eliminating 99% of it.The LEDs are great quality, diffusion is about 95% there but you can still barely see hot spots. The quality of the colors is solid, white looks good, but unfortunately the EVGA x1 software doesn't sync up perfectly when using the rainbow wave setting.I'm realizing I am really nitpicking, but it is what it is.
Eli's Two Cents
2025-07-06 18:30:28
Problem: My 3080ti is very heavy & sags on the end - with enough heat cycles this can permanently warp a card.Possible fix: Jerry-Rig a pulley & hook system with a cable to “lift†the hanging or drooping edge of the GPUReal Solution: Coolermaster GPU Bracket with RGBI bought this for 34 bucks which is around the ballpark for other GPU brackets but this one comes from a reputable company & had ARGB lighting. Opened up the box and all the parts needed for a install were present. I simply removed 3 nuts from the peripherals/GPU rear bracket & installed this in place. I used my original screws but the supplied screws also work fine, they were identical/industry common thumbscrews. The bracket itself is of thick carbon steel & appears a powdercoat or thick paint is applied, well done. It’s not aluminum and has no flex to it.Installed in place, plugged in the ARGB cable to the header on my motherboard, no extensions or plugs or adapters were needed. It’s a basic 4 pin ARGB (3 pins active, one pin blocked or not present). My ASUS motherboard recognized this without software or downloads, it simply controls it and matches all the lighting on the case. I didn’t take a pic after I changed the color of the ARGBs for the case but they all work in tandem, nothing special needed. RGB is great but why did I buy this:The damn droop I was having on this heavy EVGA 3080ti FTW graphics card - Now, It’s completely gone. The bracket comes with a smaller vertical bracket with thumbscrew used to set the height/offset required to get your particular GPU at the needed height to prevent eventual damage to your precious GPU. I set the height I needed, eyeball measured it and bam, done. I took some pics with a ruler/triangle scale to show the end result but trust me, this thing is cheap (relative to a 1,500 graphics card) and it simply works WHILE looking good. I bought this with my own cash, no association or relation to the Coolermaster peeps.RGB added .0788fps to my gaming sessions, I think.
Steve H
2025-07-04 16:02:05
Does what it is designed to do, holds up a heavy Gigabyte 2070 Super 3X OC and looks good doing it. RGB easy to configure and match to the rest of the setup. âï¸âï¸âï¸âï¸âï¸
Tedeka
2025-06-11 12:30:49
The media could not be loaded.
Bu7md
2025-04-10 11:21:50
It's good it holds my huge RTX 3070 and fixed the sag. But the installation is a little bit tricky. Not that easy if I close the screws too much, it won't be straight, and if I keep it loose, the brace will sag.But after installation, it looks very nice, especially the ARGB strip I control the led with Asus Aura, and everything is excellent.
Emmanuel
2025-02-16 21:13:26
En general el producto es excelente, muy bonito soporte para tarjetas de video, el problema en mi caso no calcule bien el tamaño de mi tarjeta (RTX 3080) con el soporte y no le quedo. Yo les recomendarÃa a los poseedores de tarjetas de la serie 3000 midan bien su tarjeta antes de pedirla, yo tuve que realizar devolucion.
Aseel
2025-01-29 11:09:32
Rgb Ùيه جميلة
Recommended Products
