Your cart is empty.
Your cart is empty.Product Description
Submersible and Waterproof
Fit for under 80ft width boats, RVs, jet ski and utility trailers. The lights are definitely waterpoof and submersible.Please make sure wires connect correctly and no electronic short before marine/underwater
DOT Compliant
100% comply with DOT standards
All LED Tail and Side Marker Lights
Super High visibility and Longer Lifetime LED advantage! Right Tail Light have 16LEDS : 12 rear facing large LEDs and 4 SMD LED-on Side Marker. Left Tail Light have 19LEDS : 12 rear facing large LEDs ,4 SMD LED-on Side Marker and 3 white LEDs facing down(For license Plate illumination)
Very Bright
Brighter & Safer
Ground Connection
When connect the wires, please especially note the white ground connection. Please insure the lights are really connected to the ground and form a closed cycle.
SIZE
Len cover: 4.5"x4.5"
Hight: 5"
Width:1.5"
Dick Winters
2025-07-11 18:11:09
The product was exactly what I wanted for my boat trailer lighting. It was delivered super fast, it is waterproof, LED, could not have been easier to install. Had them mounted in less than 20 minutes. Five stars on this!!!
Jeff Bandoch
2025-06-10 18:37:01
Worked great. Easy installation.
Gary W.
2025-06-07 15:32:13
My favorite characteristic of these lights is the slim depth profile. Less plastic exposed to get cracked. My original set were/are installed on a low profile utility trailer, since sometime during 2023. To me, the LEDs are correctly bright, even the small side one which I can see from the mirror at night. Despite the subjected road impacts common especially on trailers and longer work trucks, only recently on one of the lights 2 of the leds got weak. They are sealed units, even with the skills, it probably is not cost feasible to attempt repair. Though never backed into the river, they have been dunked under water and road spray with never a problem. I recently purchased several more sets to upgrade a couple other trailers, and yes replace one of the original ones that I had finally crack the side lens off.
reel busy
2025-05-22 18:37:46
They are wired and install as you'd expect in your standard mounting. Thin profile, i've dunked them in salt water many times. I installed a set on a jon boat trailer too i broke them myself prepping for hurricane but ordered another set which must mean i like them.
David D.
2025-05-07 14:23:00
I'm basing this review on my 1998 Ford Explorer and a cheap 8ft utility trailer with standard 1157 bulbs.I did NOT need to install resistors with this CZC LED light. This is important if you pull your trailer with an older model vehicle. Since LED lights require less current than standard halogen bulbs, some brands require resistors to prevent hyper (super fast) blinking when used with an old car. Thank you, CZC for a product that seems to avoid that problem. These lights very easy to install, because they matched up perfectly with the holes used by my old trailer lights. Actually, I did not even need to drill separate holes for the ground wires; my entire trailer is GROUNDED, so I simply attached the ground wires to the mounting bolts. IMPORTANT: check your trailer wiring BEFORE ordering this item. This kit consists only of two lights with short wires and mounting hardware. If you need to replace faulty wiring and side lights, CZC offers a complete kit for about ten bucks more. If your installation fails, most likely the problem is because your trailer is not properly grounded. Ground wire needs to be in direct contact with Bare metal (not rust, paint, plastic, carpet, wood, etc.) The white wire coming out of your harness is the Ground. Make sure it is screwed into a metal part of your trailer. The brown wire wires are your tail lights; both left/right should be lit when headlights are on. The green wire on your trailer operates the turn signals on the starboard (right) tail light. The yellow wire operates the port (left) side. The CZC light fixture has two white wires. The white wire with the "O" ring is the ground; secure it to the mounting bolt with a nut. The other white wire attaches to the appropriate blinker wire. CZC used white instead of green or yellow because the light can be mounted either port or starboard to illuminate your license plate. Trust me, this will make sense when you do the install. Again, use a test light or volt meter to insure you are getting ample current through your trailer wire system before installing lights. Old corroded wire tips might need to be snipped and restripped before connecting to the new fixtures. Excess wiring should be secured with zip ties to prevent dangling. Wow, these CZC lights are bright! Easy to see turn/brake signals in broad daylight. Submersible.
Mike O
2025-04-30 15:25:54
These worked perfectly as a replacement. What happens when ya borrow a friends trailer!
Marea L.
2025-04-29 16:43:41
Lights are very bright and seem well made. However they are not universal in regards to the mounting points. Look at the picture of my trailer light bracket. If yours has an overhead cover, as in an upside down L shape like mine these will NOT work for you. They are fine for a flat plate mount, bumper mount, or fender mount as long as there is nothing overhead to block the installation. I sold mine locally and bought a set on here with the traditional 2 screws out the back mounting system.
Joe
2025-04-08 16:18:19
Good quality, water tight, looks great. Seem durable at a great price.
Allison B
2025-03-22 12:59:11
Lights are super "bright , and all hardware was included +wiring instructions making the installation very easy. Would recommend this product.
jim Melvin
2025-02-18 12:52:16
they work perfect
Brent McIntyre
2025-01-25 10:32:45
Used on 15ft zodiac boat trailer. Very easy installation, cut and connected to existing wires, white attached to frame. Done in 20mins, Thank u.
Jer
2025-01-14 13:01:10
Easy install great price
Summer Smith
2024-12-31 20:01:03
Ideal replacement taillights for our trailer for a reasonable price.
Recommended Products