Your cart is empty.
Your cart is empty.Product Description
FB
2025-08-22 15:35:28
Fantastic basic servos. I bought 40 of them for projects due to them being on sale at 2.50 each.3 of the 40 had positional issues (twitches and whines) but were fixable.1 needed re-soldering of the Pot, 1 had a bad capacitor on the motor terminals causing feedback, and one had a bad pot.I didn't actually fix the last one but instead, I converted it to a continuous rotation and then used it to drive a robotic joint that had its own positional Pot that was then connected to the original pot's terminals. It's a good way to increase the torque of a servo if you can deal with the speed loss. (mind that slowing the output works but gearing it for speed increase causes issues as the PID formula the control chip uses will constantly miscalculate inertia and it will overshoot routinely)Overall, at this price, they are a fantastic buy.That said, I wouldn't use them for constantly holding heavy-torque applications. They tend to start heating up if holding a load of more than ~400g/cm and that gets worse as the voltage gets higher. I advise designing for 5 volt supply.If you need holding torque, look at the FAN25/30/35/etc brushless servos (also more power efficient by about 20% in this case). It's just that brushless servos are 10 times more expensive and aren't really worth it for just experimenting.
Evan
2025-08-16 10:47:34
Very impressed for low cost amazon servos, these are great for robotic projects with the RPi or Arduino. Despite having metal gears they were extremely easy to 360 mod, simply remove a metal pin on the output gear and disable the potentiometer. Without 360 modding they have 180 degrees rotation. They are very high torque compared to normal RC steering servos, which does mean that they are slighty slower. Might be a tad slow for a car steering servo - I compared it to my futaba S3003 steering servo and it makes about 7/8 rotation for every 1 rotation the S3003 makes. Overall highly impressed and surprised.
Rajini adiga
2025-07-11 12:10:36
very nice product
brown
2025-07-06 15:49:13
look fine - seem to work as they should
Kattmandu
2025-06-30 10:39:47
Can't beat this price point. These are great servos for what they are. These are not intended to replace high-end servos meant for racing but these will do well to replace a servo that went bad in a Traxxas RC. An excellent servo to put in your basher RC. They have very good customer service as well should you have a problem with any of the servos at the time of purchase.
Michael Ferry
2025-06-29 14:20:22
I ordered the set of 6.I'm using them in a robotics project, the chipo hexapod by makeyourpet .comAt this price point, these are a great deal.They showed up quickly, they were packed well, they have all the hardware shown in the photos: the different plastic hats, rubber standoffs metal standoffs, black center screw, and regular scews.They have a good strength, react and move quickly, aren't too noisy, and they were all well calibrated.The build quality and components are all good for this price point, they didn't feel cheap or crappy, but they didn't feel super nice either.I'm using a 5v power bank through a pimoroni servo 2040, and I haven't had any issues driving these.Solid, will buy more for future projects.
Curtis H.
2025-06-20 19:42:20
These work pretty good and are easy to implement on an Arduino. I was able to use them for quite some time. They don't last too long though. I purchased these about a year ago. One of them died within a week of first use, the second one just barely bit the dust. I wish they were a bit more durable. But for $5.00 each, I guess you can't expect too much.
Colobok2016
2025-06-18 15:00:11
I got this servo on time and well packed. Each servo came with four different adapters and set of screws to fix servo itself, fix adapter on shaft and four small screws to fix adapter to your part. I used five of them to assemble DIY robot manipulator. Looks like it worked fine but I did not finish project yet.
Cristian
2025-06-06 12:03:27
Me han sido de gran utilidad en trabajos con cargas pesadas (brazo robótico de casi un kilo)
Modyturkey
2025-03-24 12:54:20
Its poor quality chinese servo not a deegoo brand be careful
glynn
2025-03-10 17:12:55
good value works perfect
Omar
2025-03-02 11:52:56
me gusto sirve demasiado bien para diversos trabajos y los engranes de metal evitan que se barra con facilidad y adema soportan un poco mas
Tu T.
2025-02-01 14:47:07
But sending the wrong one with the brand call Tower Pro.
Recommended Products