Your cart is empty.
Your cart is empty.This exhaust flange stud and nut are designed to match the fit and function of the original hardware on specified vehicles. Made of quality materials, this hardware is engineered for reliable performance.
Customer
2025-08-12 17:26:00
Does NOT fit Dorman exhaust manifold 674-196. The holes in the manifold are too big. The Dorman manifold comes with new bolts.
BBent
2025-07-23 10:17:39
I'd recently replaced a rear main seal in a jeep 4.0l. The factory clip on nut/retainers had been getting loose so i figured id replace these. The initiall install I was dreading pulling the studs thru the manifold flanges due to tight work space from underneath. I happened to have plenty of anti seize for the install & theyve yet to back off, thanks!
Connor
2025-06-29 16:02:47
Had to get two sets because the first stripped out. Second set I was more carful with and seem to be holding up well. Only been on for a week or two.
LPUIG73
2025-06-26 13:58:45
Fit perfect. Use an extension and a swivel for the ratchet for easy loosening of the old bolts and tightening the news ones..
John Franklin
2025-06-24 18:47:07
SAVED MONEY BY USING THIS PRODUCT
GARY IN AZ
2025-05-21 18:57:43
Perfect replacement. Installation tip: Drive the old ones out from the bottom with a hammer and a 6-12 inch rod (1/2 inch extension works great). Drop the new studs in place, place a over-sized nut on the stud and then thread the supplied nut on using the over-sized nut as a temporary spacer. Tighten the nut until the head of the stud is seated. Remove nut, return the over-sized nut to your junk drawer and reinstall you exhaust.
Savage Henry
2025-05-16 13:59:43
Worked fine on my 1988 Renix XJ 4.0 when I sheared off one of the old bolts. Bash the old ones out with a big punch or bolt and a 5lb sledge, and bash the new ones back in with the same sledge. Use anti seize on the nut threads if you have some, to make it easier on yourself in the future.
Res2429
2025-04-19 16:22:07
Used then for exhaust pipe.
Customer
2025-04-12 17:31:22
Does NOT fit Dorman exhaust manifold 674-196. The holes in the manifold are too big. The Dorman manifold comes with new bolts.
BBent
2025-04-09 17:44:24
I'd recently replaced a rear main seal in a jeep 4.0l. The factory clip on nut/retainers had been getting loose so i figured id replace these. The initiall install I was dreading pulling the studs thru the manifold flanges due to tight work space from underneath. I happened to have plenty of anti seize for the install & theyve yet to back off, thanks!
Connor
2025-03-27 21:44:00
Had to get two sets because the first stripped out. Second set I was more carful with and seem to be holding up well. Only been on for a week or two.
LPUIG73
2025-03-10 11:14:55
Fit perfect. Use an extension and a swivel for the ratchet for easy loosening of the old bolts and tightening the news ones..
John Franklin
2025-02-21 11:05:45
SAVED MONEY BY USING THIS PRODUCT
GARY IN AZ
2025-02-09 13:10:00
Perfect replacement. Installation tip: Drive the old ones out from the bottom with a hammer and a 6-12 inch rod (1/2 inch extension works great). Drop the new studs in place, place a over-sized nut on the stud and then thread the supplied nut on using the over-sized nut as a temporary spacer. Tighten the nut until the head of the stud is seated. Remove nut, return the over-sized nut to your junk drawer and reinstall you exhaust.
Savage Henry
2025-01-02 17:54:32
Worked fine on my 1988 Renix XJ 4.0 when I sheared off one of the old bolts. Bash the old ones out with a big punch or bolt and a 5lb sledge, and bash the new ones back in with the same sledge. Use anti seize on the nut threads if you have some, to make it easier on yourself in the future.
Res2429
2024-12-29 15:31:25
Used then for exhaust pipe.
Recommended Products
$34.99
$ 18 .99 $18.99
$44.99
$ 23 .99 $23.99