Your cart is empty.
Your cart is empty.Customer
2025-09-04 16:51:41
Ironed on and sticks well, looks great. A little more money, but I thought it was worth it. Perfect for white oak edging.
A + R
2025-07-30 14:14:41
I have purchased some other brands of edging and was very disappointed on the quality and looks of them. I finally decided to pay a little more and got this. Wasn’t disappointed at all. Thickness was great and it was really easy to use. Color was a prefect match for my oak plywood. Paying more was well worth it for the quality you get. Wish I came to this realization earlier.
Mkhunley93
2025-07-18 17:33:16
This veneer goes on fairly easily with any iron...I used a cheap folding travel iron without issue. There were a few places where I had to go over it a second time and press on it with a flat board, but overall it works well. If your edges are not flat, you'll need to sand down any imperfections. Once cooled, it stays in place well and can be sanded without worrying that it will break loose. Takes stain beautifully and matched the 3/4" oak I used perfectly. Gives a very professional finish.
ths
2025-06-28 10:44:01
Quality of the Edgebanding is good. But the issue is that the strip is just barely wider than 3/4, which means you have very little room to play with when applying to plywood. If you’re careful, then it’s fine. But any little shift, you may find the edgebanding not covering the plywood. It’s not hard to fix (just heat it and shift it) but wish the edgebanding is just slightly wider.
G. Ramsay
2025-06-17 20:09:24
As someone else mentioned, the banding will cover 3/4 inch plywood, but there's not much excess. I used blue masking tape spaced out to hold it in place while I ironed on the banding. It turned out great.
Edward M. Gilbert
2025-06-08 10:41:14
The glue on this edge banding was very adherent to the plywood edges. There were no flaws or joints in the banding, unlike some other edge banding I have purchased in the past. I will purchase again when needed.
Betty S
2025-05-05 11:03:19
The perfect size for finishing 3/4†white oak plywood. Good adhesion and easy to sand down to size. Takes stain and wax finishes just as well as regular oak. Would buy again
elly_etc
2025-05-01 11:46:59
Used for a shelf to cover the plywood edge and it came out nicely. Was easy to use. I taped it down before ironing it. Sticks well.
Jimmy Huynh
2025-04-13 10:05:46
The white oak edge banding is easy to apply and the veneers are consistent and realistic. It matches perfectly with my 3/4" white oak plywood to cover exposed edges. However, 50 feet goes by quickly! I’ll definitely be getting it in bulk next time.
Customer
2025-04-10 11:54:42
Ironed on and sticks well, looks great. A little more money, but I thought it was worth it. Perfect for white oak edging.
A + R
2025-03-18 15:16:37
I have purchased some other brands of edging and was very disappointed on the quality and looks of them. I finally decided to pay a little more and got this. Wasn’t disappointed at all. Thickness was great and it was really easy to use. Color was a prefect match for my oak plywood. Paying more was well worth it for the quality you get. Wish I came to this realization earlier.
Mkhunley93
2025-02-20 12:24:03
This veneer goes on fairly easily with any iron...I used a cheap folding travel iron without issue. There were a few places where I had to go over it a second time and press on it with a flat board, but overall it works well. If your edges are not flat, you'll need to sand down any imperfections. Once cooled, it stays in place well and can be sanded without worrying that it will break loose. Takes stain beautifully and matched the 3/4" oak I used perfectly. Gives a very professional finish.
ths
2025-01-23 18:10:40
Quality of the Edgebanding is good. But the issue is that the strip is just barely wider than 3/4, which means you have very little room to play with when applying to plywood. If you’re careful, then it’s fine. But any little shift, you may find the edgebanding not covering the plywood. It’s not hard to fix (just heat it and shift it) but wish the edgebanding is just slightly wider.
G. Ramsay
2025-01-03 11:14:19
As someone else mentioned, the banding will cover 3/4 inch plywood, but there's not much excess. I used blue masking tape spaced out to hold it in place while I ironed on the banding. It turned out great.
Edward M. Gilbert
2025-01-02 10:43:40
The glue on this edge banding was very adherent to the plywood edges. There were no flaws or joints in the banding, unlike some other edge banding I have purchased in the past. I will purchase again when needed.
Betty S
2024-12-18 16:44:33
The perfect size for finishing 3/4†white oak plywood. Good adhesion and easy to sand down to size. Takes stain and wax finishes just as well as regular oak. Would buy again
elly_etc
2024-12-11 10:35:35
Used for a shelf to cover the plywood edge and it came out nicely. Was easy to use. I taped it down before ironing it. Sticks well.
Jimmy Huynh
2024-11-29 16:49:52
The white oak edge banding is easy to apply and the veneers are consistent and realistic. It matches perfectly with my 3/4" white oak plywood to cover exposed edges. However, 50 feet goes by quickly! I’ll definitely be getting it in bulk next time.
Recommended Products
