Your cart is empty.
Your cart is empty.
LENGTH: 18 feet
MATERIAL: EPDM Rubber with Acrylic Foam Tape
COLOR: Black
FEATURES: Isolates Vibration， Minimizes Friction， Provides Protection, Eliminates the risk of pinching rocks and debris between the fender flare and the body of your vehicle.
INSTALLATION NOTES:
1. Because this T-shaped rubber trim has a double-edged structure, which is thicker than ordinary rubber trims, if the fender has a 90-degree or acute-angle curved edge, this part will form a wrinkle. It is recommended to trim at the 90-degree point by using a razor. Make them look as seamless as possible.
2. In order to make the flare trim and the fender flare firmly adhere, prep the surface ensuring no dust or moisture is on the fender flare before installation.
Juan Pablo The Pool Guy
2025-09-03 14:19:16
Used this to replace the C-channel style that came with the flares installed on a Tundra. Driving desert dirt roads the mesquite and creosote brush pulls the edging off. Also, the original edging wouldn’t stay in place around the gas filler cap. This took a little practice to get on but once it’s in place it adheres well. I’ve had no problems with it coming loose or tearing off.
SuitsD
2025-08-25 12:59:07
This is easy to install, peel and stick, and you can measure to length and cut what you need. Works really nicely at sealing off my fender flares and protection of my doors. ALOT cheaper than buying 15 feet for Orielly and Autozone
Gerald Banks Jr
2025-08-09 14:58:11
Used to help make a seal for my fender flares. Easy to install well worth the money
Charles Lee
2025-07-18 18:20:36
I see some reviews stating that the adhesive isn’t good or it sticks to itself and hard to peel of if it gets stuck to itself or it’s not self explanatory. There’s enough for all 4 fenders and there will be extra for 2 fenders just in case.1) just make sure the surface of adhesion is clean and dry2) as you are attaching the beginning, go slow, put pressure so it sticks well, don’t try to stretch it to save extra because at the end you’ll have places where it’ll come right off, as you move along you will slowly peel of the adhesion sticker.3) after installation if there’s small wavey areas just run your finger through the whole strip and it will flatten itself out and then cut off the excess.4) you gotta let it settle overnight and not let it get wet for maximum adhesion.
ksarks
2025-07-09 11:39:32
Was really happy with the look basically identical. Was worried about them being too bulky but they look amazing. Definitely recommend for someone looking for a cheaper route then OEM like myself.
Crazy X
2025-06-22 14:27:04
Once I found my order at the wrong address I was good, first of the flare gasket was packaged perfect in a ziplock clear plastic bag rolled neatly. The edpm was perfect very easy to work with. Installed the gasket on both rear flares without any problems, once I was through before placing my flares back in place I went back over the gasket to make sure there wasn’t any movement . Once I finished installing my rear flares I liked the way the gasket was pressed up on the body of my Ford Superduty no gaps at all. I highly recommend if anyone is looking for replacements for their flares get these you won’t be sorry. I will update after a few weeks on how the gaskets hold up. I will add a couple photos also tomorrow.
Mike F.
2025-06-07 16:05:53
Got this to fill the tiny gap between my fenders, but this didn't stick very well and kept falling off
Reb
2025-05-15 18:27:49
They should make the gap wider to make it easier to apply to fender flare. It’s not easy to get these on. Took me about 30 minutes per flare to apply
Flash
2025-05-14 18:14:24
Works perfect just make sure you clean the area really good then pull off the red backing about 1 inch from the end then install then slowly remove the backing and press down on the backing as you go along, make sure to install when it's warm out for better adhesion or use a blow dryer or heat gun
MKrimo
2025-02-05 11:19:42
Le rendu est sympa, par contre je ne pense pas que ça durera dans le temps, ça ne collait pas très bien.
Luke Holmes
2025-02-02 13:35:14
Love that it has double sided tape to make it super easy to apply, makes the finished product look professional
Sam C
2025-01-14 16:33:01
I repainted my fender flares and had to peel off the original tape that came with them. This tape works great, it’s holding up well and saving my truck paint from getting gouged with the flares edges. definitely worth it ðŸ‘ðŸ»
Gerry
2024-12-01 16:16:35
was ordered as a product which works with flares purchased however does not work with flares ordered
Recommended Products
