Your cart is empty.
Your cart is empty.1PCS :Good Quality Modified Key Blank Please verify original remote does not have a red or green light, this part is not compatible Pls cut the key blade, take the internal electronics (include immobilizer/transponder chip) from your original remote and place them to our key shell, then it is OK! There's no programming needed This item isn't a remote key, it's just a remote key shell. NO (remote/electronics/ignition or transponder chips).
Doogie
2025-08-19 16:23:58
This a good value, and works fine, but you will either need to have the new key blade cut at a dealer, or you'll need to replace the blade with your old one. The parts that make up the pivot that the blade swings on are slightly different. I saw a review on here that recommended using a pick to drive out the roll pin to swap the key blade. DO NOT USE A PICK. A pick is tapered like a wedge and when you try to drive the pin out it will very likely break the cast metal pivot. I ordered 2 of these fobs and destroyed the first one this way. I found that an 18 gauge brad (nail) was the perfect size. A brad is also tapered on the end, so I clipped the tip off with a pair of wire cutters and filed it flat on the end. A light tap from a small hammer easily popped the roll pin out of both the original key and the replacement. Lay the pivot/blade assembly on a block of wood with a hole drilled in it so the roll pin is over the hole. Drive the pin out with the modified brad held with a pair of needle nose plyers and it will drop right in the hole instead of flying off somewhere. Off to order a replacement fob for the one that was destroyed by trying the pick method
Manuel E Roldan
2025-08-03 17:33:03
Not an exact replica. Can’t take the blade from the old and put into the new because the button doesn’t match exactly. Sad because it seemed like good quality. Wasn’t even worth my time to send it back. I just tossed it I was so upset. I’ve bought and switched a total of seven from different cars and this was the first and only time I’ve had a problem.
rasj
2025-07-22 16:41:24
I replaced my 13 sonic key fob, I used my my own circuit board and used my key. I did have to take the pin out of the roller to use my key. Works perfect. There are YouTube videos that show you how to do it. The hardest part was to separate my old fob
Richard
2025-06-14 14:51:38
Seemed nice at first but with the key riding around in my pocket after about a month the rubber buttons started to stretch and after about 2 months the key fully snapped off. I have to start my car by inserting that key piece into it then jamming this fob onto it becaus it's a chip key. You get exactly what you pay for.
Customer
2025-05-18 13:06:50
Case fits great.Mine required me to unpin the blank key and my original and swap them.Mine also required filing down the end that gets pinned in so it would fit.Took about 1 hour to swap prob 30-40 minutes were to do with modifying the original key to fit. My car is a 2016 cruze (1st Gen, yes they made them that year).
furd
2025-04-11 12:28:39
I'll skip all the other tricks/tips I have seen on Amazon and get straight to the point. Many have noted the old key component doesn't fit, these replacements differ slightly in the hinge depth and the button hole causing it to stick or not close all the way. The solution is NOT to go spend $20+ at dealer to have new key cut. Rather knock the tiny roll pin out of old and new then slide old key bar into new metal hinge/elbow piece. The trick is finding something tiny enough as its approx 1mm in diameter. I tried a few different small punches and allen keys but they were hair too big for pin-hole. Then it dawned on me I have an inexpensive mini-pick set from H***F***. Tapped out enough with 90' pick to grab other side with needle-nose and pulled roll-pin out. Slid the new bar out and old bar in, lining up the bar's groove to pin hole. Done two this way, no issues. Attached pic of key components (elbow/bar) and pick used.
Roger Stepp
2025-03-25 10:26:44
Thet are not identical. You either have to get the accompanying key cut or make modifications for the old key to work as I did but decent quality fob. Be aware that if you have an original OEM fob, it does not pop apart easily.
D. W.
2025-03-05 09:08:22
This is not at all as easy as it seems! The key fob is easy to damage when opening to put the original chip/card in this new fob.
Jonas Florencio
2025-02-13 16:54:56
c'était exactement ce dont j'avais besoin
Edgar ruiz
2025-01-21 16:12:05
Muy buen producto recomendable ðŸ‘
Recommended Products
