Your cart is empty.
Your cart is empty.Product Description
Locking screw
With the screw, the rulers could be hold at any angle.
*Please hold the ruler when rotating the screw. Rotate it clockwise for tightening; rotate it counterclockwise for loosing.
Laser-etched ruler measurements
Stainless steel rulers with laser-etched scale.
Stainless steel rulers are finished by brushing craft. The edge of stainless steel is sharp to cut papers and carve marks on wood.
*It's dangerous for kids. Please keep it away from kids.
Easy-to-get battery
CR2032 coin battery powers on the product. It's easy to get in your local store or online.
*Battery is very small. Please avoid dropping out from pacakge.
NEW BATTERY COMPARTMENT NOTICE
As required by Reese's Law (15 U.S.C 2056e, Pub. L. 117-171), we updated our battery compartment design from June 2024. It will be more difficult to open, but it is safety and reduce the risk of injury and death to children 6 years old and younger from ingesting batteries. Please be patient and follow the steps on manual to install battery.
RM
2025-09-01 11:18:52
Because of the price (a third lower than the more expensive angle finders) I was concerned about the accuracy. If not accurate, what's the point. Well, the accuracy was well above my expectations. Every angle measured was within 0.1 degrees. Usually right on and 70% of the time within 0.1 degree. Occasionally it showed 0.2 degrees off, but never more.I was also concerned about the quality and thickness of the arms. As far as I am concerned, they are perfect. Not too thick, nor to thin. Very satisfied.Hopefully they hold up over the long term, and if they do, they are a great buy.
Puddleglum
2025-08-13 14:58:50
The angle finder does its job very well. It is easy to use and responds consistently and accurately. The buttons are intuitive. The display portion does feel flimsy so don’t expect to throw it or drop it off a roof. At this price point, I can’t complain.
Douglas Patton
2025-08-05 13:10:40
I run a 20 foot press brake for a living. That is, everything I do is all about the angles. I've had all sorts of different protractors over the years, from Sterrett to Mitutoyo and five or six others. My good protractor is a Sterrett cast iron job from a combination square set I bought for a couple hundred bucks. I use both the tri-square, and the protractor every hour of every day.But this thing, cheap as it is, blows them out of the water like a nuclear torpedo.Seriously, this has cut in half or more the amount of time I spend checking angles. It's accuracy is decent (certainly within the 1/2 degree shop tolerance we have) and it is extremely easy to use. The digital readout is easy to read, which is a blessing for my poor worn out eyes. (I can barely read my old Sterritt without reading glasses, which I can't wear while running my machine. So I was constantly switching glasses. Yeah, I have bifocal safety glasses, but they're a pain to use when running my machine.)But there are some down sides. Down sides I will happily live with.First, this thing is very cheaply made. In my environment I don't expect it to out-last the batteries. This is okay. For the price and the amount of time I save using it, I'll just buy another one! but it is a downside.Second, the battery is prone to falling out. Unlike some other devices, you can't easily tape the battery compartment closed either. But oh well. It doesn't fall ALL the way out, just enough where it shuts off. Push the tray in and all is well.Third, it doesn't remember it's zero after it self-shuts off. No big deal, but if you leave it sit at a particular angle over lunch when you come back it will have set that angle to zero. Easy enough to fix, but a mild irritation.All these irritants aside, this is a great product for the price. It works wonders. The only reason I don't give it five stars is for the three above reasons, and I almost did anyway.If someone would make pretty much exactly this, but with a little sturdier blades and a higher quality mechanism, I'd marry it.(Note: I work in a heavy industrial job shop, the majority of the time bending 3/8 to 1/2 plate. I also bend up to 1.25 plate, and down to 11ga on occasion. All of it up to 20 feet long. When you need to go down a length of 3/16 plate 20 feet long and check for angle consistency, this has been the best solution I've ever had. Bar none.)
Max
2025-07-27 13:16:03
Works fine.
Samantha
2025-06-25 14:29:51
This tool has saved me so much time and wasted cuts for projects around the house. Priced very cheap but built way better than expected.
Popcorn maniac
2025-05-03 13:59:01
Very accurate, I cut a lot of diffrerent angles and this does the job. Also great for saw setup.
Kellip
2025-04-15 09:41:10
This isn't my first angle finder, but it is my first digital angle finder - and I love it. My husband and I had a lot of moldings to add in our 100 year old house, which is built like a tank but not exactly plumb or square anywhere. This little tool was just the thing to make sure the cuts we made were accurate. The digital readout makes all the difference. It's easy to see and read, and it's much quicker than trying to find the tiny numbers on my old plastic angle finder.
Halljp
2025-04-13 17:19:40
It was a pain to get the battery door to release. It would release on one side and get stuck on the other. Was OK once I got it open, but it was frustrating enough that I almost returned it. Now that has opened once, it seems to release fine now. Operates fine and lock works well.
Ian
2025-04-09 18:34:51
Should have bought one years ago. So easy to set Angie’s on my table saw. Accurate cuts.
jorge alberto luna soto
2025-03-25 15:48:05
De gran utilidad para obtener falsas escuadras, conocer ángulo interior y/o exterior de algún elemento. Uso general en carpinterÃa, albañilerÃa y herrerÃa entre otros. Fabricado en acero inoxidable y a un costo aceptable..!
XenomorphUK
2025-03-15 13:28:59
I am currently fuuly renovating a house and one of the many jobs it to either fully replace the stairs or renovate what is there.This has primarily been bought to identify the angle of the stairs so that if we go down the route of renovating, it will give is the angle of the stairs so we can see if off thet shelf items like the glass sides can be bought.Came well protected, good instructions that are easy to follow and when using on known angles, works a treat. Accuracy was very good, there is a tolerance of error but for what im using this for, its well within what i need even if slightly out.
Hochsauerland
2024-12-28 11:13:37
📦 Verpackung:Das Produkt war sicher in einem passenden Karton verpackt und gut geschützt.💰 Preis & Leistung:Unsere Meinung und Recherche zufolge bietet das Produkt ein gutes Preis-Leistungs-Verhältnis in diesem Bereich.🛠Verarbeitung/Material:Die Verarbeitung des Produkts ist sehr solide, es ist sauber und präzise gefertigt. Das verwendete Material entspricht den üblichen Qualitätsstandards.📠Größe:Die Abmessungen des Produkts entsprechen exakt der Beschreibung und erfüllen somit unsere Erwartungen.👀 Aussehen:Das Produkt sieht genauso aus wie auf den Abbildungen dargestellt.âš™ï¸ Technik & Funktion:Das Produkt erfüllt den beabsichtigten Zweck gut, entspricht unseren Erwartungen und funktioniert einwandfrei ab dem ersten Einsatz.📦 Lieferung:Die Lieferung erfolgte innerhalb des angegebenen Zeitraums und das Produkt kam unbeschädigt an.
Pedro
2024-12-11 12:41:29
La verdad que si quieres hacer angulos perfectos con tus herramientas es imprescindible este producto
Recommended Products