Your cart is empty.
Your cart is empty.Product Description
Specifications:
Diameter: 28.5mm
Length: 40mm
Pin Length: 8mm
The spacing of two Pin: 4mm
Light Color: Cool White (7000-7500K)
Input Voltage: AC12V / DC12V-24V
Wattage: 2W
Lumen: About 258 Lumens
Base: G4 Sockel (G4 Bi-pin)
LED Type: 24 Pcs Super Bright 2835 Chip SMD LED
Note
We provide the superior-quality products for each customer.All the items in my store my company QC have tested it carefully.
Make sure this is the correct type of bulb before placing order. Base and voltage should be fitted.
Features:
*Light weight and stable performance.
*High quality and super bright LED bulbs.
*Easy plug and play. No other tools needed.
*Extremely long service life. More than 50,000 hours of theoretical service life.
jjcorb
2025-08-12 20:58:05
Best I have found so far. Hoping they don't dim, flicker or burn out quickly like so many others.
GerriB
2025-07-28 18:41:11
My MH uses these bulbs in my overhead lights. Works great
Max
2025-07-01 10:24:40
Would but again
JYSE
2025-06-17 16:56:14
If you have round puck housing for the G4 light bulbs, these flat circular one-sided LED lights are much brighter than the T4 JCD type. The 24 each 2835 SMD LEDs are very uniform and stable. Now I can see what I am cooking. :-)
Christina Kendrick
2025-05-11 13:55:20
I have IKEA puck lights in my kitchen as undercabinet and top of cabinet uplighting. The 10W halogens are a pain to deal with, require fiddly installation to avoid contaminating the bulbs with oil, are constantly burning out here and there, and throw a decent amount of unwanted heat.After finding these COB style wafers I decided to bite the bullet and do a swap. I didn't want to use LEDs that try to be bulb shaped because LEDs shouldn't be used in reflector housings as the light pattern usually looks like garbage.Upon initial installation they were great, the light quality is good, it's not great, but good enough for my purposes. However, I have simple AC/AC transformers taking 120V down to 12V because the original IKEA power supplies have all killed themselves with heat. Those did put out DC current.These lights do flicker on 12V DC if they are the only load on the circuit. It's fairly annoying and I was seeing it all the time. I got 12V DC drivers to swap my transformers with but haven't taken the effort yet to do that. In the meantime, if each circuit has 1 halogen bulb in it, essentially a resistive load that smooths out the AC, the lights flicker a little, but it's well within my tolerance.I'm somewhat disappointed because they do have a nice sized electrolytic cap on the board, but it must not be enough to smooth out the AC.
marilyn mellody
2025-05-09 12:18:17
product works great for what i need it
S. Fischer
2025-04-05 13:04:34
We have a 2010 Tiffin Phaeton MH which originally came with halogen bulbs in the ceiling lights. We replaced those in short order (in the first year of ownership) with LEDs purchased from the supply which Tiffin was using at that time (at a cost of $7/light for 58 LEDs).As time went by at least half of the new LEDs had partially stopped working or, worse yet, began a bit of flickering.We finally decided to replace all 58 LEDs with new ones. It's always kind of risky purchasing "sight unseen" lights here on Amazon (as I've done a couple of times). I decided to give these a shot. I selected the "Cool White" bulbs in packs of 20. Price came out to $1.79 per bulb.I was a bit apprehensive after reading another review in which the owner had to remove the black plastic insulator and cut the legs a bit.I have included a picture of the true measurements for this LED as the description concerning overall length is wrong. The description is 45mm in total length, but mine were actually 39mm. The height of the electronics on the back of the board bothered me also, but the total thickness is 7.85mm and posed no problems. I appear to have the same ceiling sockets as the other poster, but I did NOT have to remove the insulators nor clip any of the legs.I just installed these, so I cannot address longevity, but I love the color (which I would describe as "Bright White".
Customer
2025-02-26 15:56:47
I bought these and installed them last April and have not had one go bad. Reasonably priced and as you can see in the photos, provide much more light than the “yellow†OEM bulbs. There is a slight mod you have to do to these to get them to fit into the light fixtures. The two pins need to be trimmed to about half the length and then the little black spacer bar needs to be removed. After that, they fit and provide all the light you need.Prior to purchasing these, I bought another brand and installed them. Within 1-2 weeks they would start flickering and then really start "strobing". (Too old for the strobe lights). Found these and upon the recommendation of another RV'er, bought and replaced all 60 lights in my motorhome. Now you can see me across town. I love them.
æ‰å±± 昌好
2025-02-19 18:52:41
クルーザーã®å®¤å†…ç¯ã§ä½¿ç”¨ã—ã¦ã„ã¾ã™ãŒã€ç´”æ£å“よりもã€ã¯ã‚‹ã‹ã«ä½Žä¾¡æ ¼ã«ã¯é©šãã§ã™ã€‚
Gareth
2025-02-16 13:31:14
Very good
Keith Green
2025-02-06 16:49:08
Talk about an easy upgrade, these lights were so easy to install, and are bright enough we only need a few on, as before we would of have most of our lights on. They use a lot less power, so your unit batteries last longer before recharge, and they don't get hot, which the old style did. For the price, compared to the RV dealer, less than half, and good quality.
RAPUNZEL
2025-01-13 11:19:06
These bulbs have replaced halogen lamps and are just as bright. Also saving lots of battery power on my RV
Glenn Schulz
2024-12-05 13:53:23
I used these in my RV, it’s a perfect match as far a color to what I had. With the stated color temperature of these lights, I was concerned that they might be on the purple side but they are a very bright white light. The only issue is the pin spacing is not correct. It’s not difficult to bend them with needle nose pliers to get them to fit.
Recommended Products