Your cart is empty.
Your cart is empty.Lipped mounting bracket works to lift and creates greater stability. Each leveler has load-bearing capacity of 800 pounds per set.
Dusty Fellow
2025-09-01 21:05:22
I used these leveling feet on my workbench, which weighs about 200 lbs. The bench needed to be leveled with my tablesaw as it also serves as the saw's outfeed surface. Just screwed these into the bench legs and took about 10 minutes to level the bench. Still as rock solid as it was before. A quick note if it's not obvious from the diagram - you need to be able to access the leveling feet from above to adjust.I should note that the screws to mount the levelers are included, but the hex key you need (5mm) is NOT. You probably have a 5mm hex key floating around...but you've been warned. :)
NMCajun
2025-08-09 12:46:55
Looked at several different products for giving me adjustable legs on my woodshop workbench. I am very pleased with the quality of the product and the ease of installation. All necessary hardware was supplied. It would have helped if the thread size of the adjusting screw (M10-1.50mm) had been listed as I chose to buy some nuts as a locking nut once I had set the height of each leg. Delivery was less than the time estimated. Make note of the product dimensions to insure proper installation on your table legs.
Mark Colan
2025-07-26 16:27:55
These are very beefy height adjustments, handy for mobile bases with lifters, for when you want to have your power tool stationary and level. Simple to install, easy to adjust. The steel is thick enough, the holes are big enough for robust mounting screws, and the adjustment rod is a substantial thickness. Made to last.
ToolNut
2025-06-12 18:33:31
Does what it is supposed to do but rather expensive for what it is. I think a price at 50% of what I paid would have been a value.
James J. Socia
2025-06-06 09:33:22
Serves the purpose great. Easy to adjust, especially in the garage where it slopes out to the driveway. I used them on to benches that I made. I would highly recommend them to my friends.Jim
Hardwarenutz
2024-12-08 11:50:20
I bought two sets to use on a 12' workbench with eight legs. They install easy with a vix bit drill bit (self centering) and Philips head bit.I adjusted them by hand while lifting the legs with a lever. Then fine tuned with an Allen wrench. Took 20 minutes in all. Now I have a level bench in my basement workshop even with the sloped floor. Much neater than shims.Worth the price!
L. Rizzo
2024-11-26 15:25:58
I have a bed that needed to be leveled because of an uneven floor. The bed is positioned in a corner, and we roll it in and out on the bed frame wheels. Leveling it with wood blocks under the wheels was a nightmare. If it fell off the blocks while making up the bed or cleaning, it was a hard job getting it back on the blocks.So I tried using these Lifting Levelers. I screwed one into the box spring at each corner of the bed, and then lifted three corners up off the frame until the box spring was level. Now we can roll the bed out of the corner and back, and when it's back it's level. I installed one in all four corners just in case we want to turn the box spring around for even wear. Then all that needs to be done is to readjust the levelers. (Otherwise only three would normally be needed since there's always one corner that doesn't require lifting).The only other important thing to add is a small block at the center of the long dimension of the box spring on each side, since the box spring should not be supported only at the head and foot of the bed. If you want to be fancy, you can use Combination Leg Equalizers instead of little wooden blocks.
Franc
2024-11-18 11:21:36
These work great! Stirdy and solid and take all the weight that I've applied to them. easy to install and no issues to speak of, yet. Another quality product by Rockler. I give it 4****. Nice!
Recommended Products
$1,518.97
$ 99 .00 $99.00