Your cart is empty.
Your cart is empty.Product Description
Fred
2025-07-26 13:07:27
Used these to lift, with a winch, my table saw!
Richard Solis
2025-07-03 15:45:51
The media could not be loaded.
Joe Blount
2025-06-10 21:24:49
This fit perfectly on the Vevor hoist I have. The included bolts fit the threaded holes on my hoist. The pins holding the bearings all feel tight. They look to be well made.I'm not too concerned about the weight rating. I don't need this trolley to be extra strong, I need it to help compensate for the weakness of the strut it rolls on. I'm confident the strut will fail before any trolley would fail. So I really like that there are 4 sets of bearings on each bracket. That will distribute the load across a larger area of the strut, and reduce deflection & bending. That's why I got these.Each bracket has a little rounded nub on one side that protrudes slightly past the bearings. I assume the purpose is that nub hits the rubber stopper I put at the end of the strut. Otherwise, the bearings would hit the stopper. There's no instructions, so I'm not sure, but that's what I come up with. So - I put the little nubs outward from the center of the hoist, so they'll hit the stoppers. Now that I look at my photo, I see the nubs aren't visible in the photo LOL.
Customer
2025-05-26 14:37:13
These arrived VERY well packaged, with cut foam to keep everything secure. Hardware was included for two different size mounting options, the smaller bolts worked for my application. I'm using these mounted to a hoist and with the rollers in a uni-strut channel that was mounted to the rafters in my workshop. The primary usage will be to raise a set of stairs, so I have access to the storage area behind the stairs, so these likely won't be worked anywhere near their capacity. They are well built and fit the uni-strut channel great. I had tried a different brand and they didn't fit in the channel, so I had to return them. These fit perfect and roll smoothly. The other set was a little lower profile, by about 1", which would have been preferred for my application, but these will work great.
OO
2025-04-08 15:50:46
These came very quick and are strong and heavy. I have a 2000lb hoist that I want to mount in strut channels. All I needed was the trolley. I found these and they work great. They are over rated for what I will be using and that is for safety. The bearings seam smooth and easy to roll. I have not hooked this to the hoist yet but I can tell from the way it is made that it will do what I am looking for. I read a review that said the bolts are not strong enough but I am not an engineer to know that. If replacing the bolts is what you want to do for additional security then have at it, they are not expensive and I don’t believe that changes the way this trolley will work. I like them and I will be putting them to quick use.
Nathan Hause
2025-03-12 15:35:38
The media could not be loaded.
Mark J. Hughes
2025-03-02 10:32:46
These types of devices come in two flavors -- one where the mounting plate is parallel to the wheels, and this one, where the mounting plate is perpendicular to the wheels. Not a huge thing, but make sure you get the ones that are right for your strut channel.Other than that, these seem sturdy and well built, roll great!
Jack Of All Trades
2025-01-11 18:05:09
Everything about these trolleys is great, except... (I'll get to that part later)Pros: These are fairly well designed. I like the triangular shape of the mount point, and I believe that will hold the claimed weight. The bearings are really smooth and well-greased. The welds look really solid; I have no qualms about the workmanship of the welds. They are fully galvanized and should endure the elements.Cons: The wheels are a little uneven. When rolling on an extremely flat surface, not all the wheels contact the surface. And now the "except": The mounting point for the hoist is slightly skewed about 5 degrees. You can plainly see that in the 5th and last pictures I took. Both of the trolleys have the same skew, so their alignment jig must be off. It's not a deal-breaker. If you line them both up the same way, the hoist should be skewed at the same angle. Would I get them again? Maybe.
Chris
2024-12-26 14:06:55
Very nice quality and finish. Used it for a trolley hoist. Highly recommend.
Recommended Products