Your cart is empty.
Your cart is empty.Product Description
SIZE TO CHOOSE
- 2.5 Inch
- 4 Inch
- 5 Inch
- 6 Inch
- 10 Inch
- 12 Inch
WIDE APPLICATION
These unique clamps are typically used in securing duct work, dryer vents, dust collection hoses, piping, large cable, pvc tubing and more. Ideal for use in automotive, industrial, mechanical, agriculture, boat/marine, shield, recreational vehicles, household and more. Works for both indoor or outdoor use.
ISPINNER Key-Type 304 Stainless Steel Worm Gear Hose Clamps, Clamps for Dryer Vent, Dust Collector and Automotive
HIGH QUALITY
Made of high quality 304 stainless steel with high performance of corrosion resistance and acid resistance, they are strong and durable, when installing on the pipe, you will no longer worry about them rusting and breaking.
EASY TO TURN KEY
These clamps have a easy to turn key, which is designed to make it easier to secure and un-secure on the hose. No screw drivers or socket wrench is needed any more! Just simply turn the key clockwise to tighen and counter clockwise to loosen.
Chaz S.
2025-09-01 16:50:15
I used one of these on my dryer vent. These work great if you have enough clearance in the rear of the dryer instead of the traditional clamps requiring a flat head screwdriver. Just twist until they are tight and your all set. Good quality, easy to use and tighten.
gnat
2025-08-06 18:49:16
This is so much better than compression clamps and no tools required
Alex P
2025-07-25 15:47:47
Saw this clamp on a youtube video, and got it to try since I was redoing my dryer vent hose and pipes with all new materials. The clamp itself is well made, much better than the cheap aluminum ones that come in those dryer vent hose kits.For the vent pipe side, it was easy to attach the clamp. It does take a bunch of twists to fully tighten the clamp. The traditional philips screw clamps are faster to install when you use an electric screw drill. But it is a one-time install, so it's not that bad.For the dryer side, my LG dryer has a short pipe but it is in a recessed area. The clamp can't fit exactly where it should go because the thumb screw sticks out. Unlike the philips screw types.. So I have the clamp mounted at an angle so there is space to turn the thumb screw. It works, but not ideal.If you want better quality clamps, I'd suggest getting one with the regular philips screws. Those are faster to install, and easy enough to finish with a screwdriver.
R. Zoon
2025-07-18 14:42:38
Worked great and no tools needed!
DubG
2025-06-27 19:26:49
No tools and worked on a dryer MagVent replacement for the original exhaust hose for a dryer.
K. Honeyager
2025-06-04 18:04:53
I bought these for installing a vent hose on my new dryer. I'm typically cursing during this process, but using these kept it to a minimum.
BOB
2025-05-22 14:43:49
Arrived 1-day layer than expected but good product
Pox Doc
2025-04-28 12:36:37
PERFECT FOR MY CLOTHES DRYER HOSE. It is as advertised and worked very nicely on my dryer vents and enabled me to get rid of the horrid rusty spring steel clamps that came with the vent duct. Nice shiny stainless steel with attractive and well molded wingnuts.BUT:I wouldn't even be writing this review if the spec sheet didn't designate this clamp as suitable for automotive use. For auto air or ram ducting - maybe. But I wouldn't personally use them in that sense.The worm gear is loosely fitted in a very thin housing and the plastic wingnut bottoms out on the tension band when sufficient torque is applied. I have not personally tried this product in an automotive setting because I have enough common sense and experience in that area that I wouldn't even try to use this on a 4" vehicle hose clamping application, other than, as mentioned above, on low pressure non-critical ductwork.When you get into automotive pressure applications above 3" diameter, you are usually talking about commercial uses, such as diesel engines, trucks and tractors. It is my OPINION and my OPINION ONLYthat these 4" hand-tightened clamps just wouldn't cut it because of the narrow width of the band and the weakness of the tightening mechanism. I also believe the plastic wing nuts would break off if one were to torque the band to proper spec necessary to secure a 4" engine hose. In many 4" hose applications it is doubtful that the small size of the wingnuts would allow you to achieve proper torque before the strength of your hand reaches its limits. So, then some Bozo will show you how it's done using a set of plyers which would definitely snap the plastic wings. Then where will you be? You'll be U.S.C.OPINION and Free advice-for what it's worth.
peter
2025-04-10 17:50:42
So simple to use. Attached and twist knobs. Makes dryer work a breeze.
Ian MacGowan
2025-03-30 15:42:49
Excellent. Did the job. Thumb screw is a nice touch.
JeffWi
2025-02-26 19:25:08
I like how easy these are to use
Won Hemy
2025-02-07 11:59:19
Slightly more expensive but definitely worth it if you want the embedded key. Quality of the steel seems top notch as well!
Karl Coulombe
2025-02-04 11:26:36
Fonctionne bien le bouton semble vraiment fragile. Mais pour un tuyau d'aspirateur pour l'atelier c'est parfait.
Recommended Products