Your cart is empty.
Your cart is empty.The Jonard Tools EPD-91461 Punchdown Tool with 2 Blades 66 & 110 is designed to terminate and trim wires in 66 and 110-style cross connect blocks and 110-style wall jack modules. This punchdown tool is perfect for any telecom or data communications installer. The tool cleanly terminates and trims wires in 66 and 110-style cross connect blocks and 110-style wall jack modules and also features high/low impact settings, combination hook/spudger stored in the chassis, color coded yellow and blue for ease of use, enlarged blade storage compartment for easy storage, tested up to 100, 000 cycles at high impact setting to ensure long life during use, compatible with all of our EPB-series blades and other similar brands. This product has a lifetime .
Rob Allman
2025-08-18 12:13:29
Great tool and half the price of others.
Lodges
2025-08-12 13:23:50
Great product at a great price. Much less expensive than the Fluke networks tool I lost. The kicker is the tool came with a combo 110 blade on one end and a 66 blade on the other; what a handy blade to have. Never saw one before. I’ve used both sides and worked well, very sharp. I’m happy with my purchase.
bodezutpha
2025-07-26 09:10:42
Had it for about a month and pleased with it so far. I work in the telecom industry and use punch tools daily. Construction and quality is good and comparable to a Fluke brand at three times the price. My only complaint is that I wanted to continue using my old Fluke 110 blade with the Jonard tool but it wouldn't fit when I tried to insert it by hand. My Fluke 66 blade did insert in the tool with no problem. The 110 blade would probably go in if I forced it but I'll just use the Jonard 66/110 blade that came with the tool.
Bifftheman
2025-06-11 14:23:16
This punch down tool is simply the best!Not one bad termination and 100% on all testings.I have the envy of a few coworkers who have Commercial or Fluke tools. This bad baby is hungry for Cat 6 jacks and all patch panels.A must if you are serious about your telecom job!
Customer
2025-05-29 17:39:33
Saw the price and gave it a shot. Great price and great value. Tool is well built and the combo 110-66 blade is a great feature. Would definitely buy it again.
Tim McGrail
2025-05-15 12:10:56
Seemed like a good idea so I gave it a try. First of all the blade will not lock in the tool so it is constantly falling on the ground. Tried the blade in a manual tool locks in perfectly. Secondly the tool has no power whether it’s on hi or low settings. In fact I don’t think the switch does anything. I install intercoms and was hoping to use on 22 gauge landing on 66 block. Nope. Even cat wire was difficult to cut. Good idea but very poorly executed. You’ve been warned.PS other web sites show this item as discontinued.
SkydivingNerd
2025-05-14 15:02:56
I'd have to agree with Drake's review. The 66 blade isn't sized correctly and it's hard to get over the 66 contacts. And once you've punched down the wire, it's difficult to pull the blade off. Luckily I just need it for a few punches here and there but this will really slow down anyone who has even a moderate amount of punching to do.A better quality Fluke blade might work on this tool but if you're going to spend the money for a Fluke blade you might as well get the Fluke tool too.
BrhatWeed
2025-04-30 18:54:38
Some things are better left unchanged and this punchdown tool is an excellent example of that philosophy, it works right the first time and every time after that.
Gagan
2025-04-11 16:33:59
It’s a Good Product and so far working well. Blades are Good.
Howard
2025-04-05 11:56:55
good
Mandeep singh
2025-04-04 17:01:54
Good tool worth it thanks!
Jose Angel
2025-01-08 11:04:07
LLego en su empaque correctamente , veremos que tal su desempeño en los siguientes dias , pero por las primeras pruebas esta funcionando bien
Customer
2024-11-24 17:47:29
Very well done tool! Sharp blades, it feels very sturdy.
Recommended Products
$129.00
$ 59 .99 $59.99