Your cart is empty.
Your cart is empty.Product Description
Installation Adjustable
The adjustable range of the mounting hole is 30~115mm.
Adjustable Angle
The motorcycle license plate fixing plate can be folded inward and adjusted to an appropriate inclination angle.
Stretch Adjustable
The extendable length is 21mm (0.86 inches).
Height Adjustable
The vertical moveable range is 0~38mm (1.48 inches). Perfectly adapted to the height of the rear of different motorcycles.
Keagan Mahoney
2025-08-25 14:22:07
Perfect for Crf 300l. Use lock tight!
Manny
2025-07-25 12:00:29
Just had to cut a bit of material off because my bike is very narrow. Here is a before and after. Appreciated the free lights.
Looks very good worth it for my bike
2025-07-24 09:40:40
Great on my bike
Ryan
2025-06-30 18:14:35
Bought this to replace the tail tidy on my huskie vitpilen since the trex racing one I had was brutally ugly. The actual bracket itself is much higher quality than I was expecting and seemed to be machined very well. The problem comes within how low it hangs under the frame after mounting. It will rub against the rear tire if you do not adjust your rear suspension, but then again adjusting the suspension for a license plate holder on your motorcycle is stupid to begin with. In other words don't compromise safety and handling for aesthetics.The turn signals on the other hand seem to be good quality out of the box and after a couple hours of soldering and rewiring they burn bright and didn't hyperflash on MY bike. After about a week though water had gotten into the rear turn signals but had not failed.Both items look and do their purpose just not as well as oem.
SlumDiggity
2025-06-09 15:40:06
Fits perfect for my 2007 ninja Kawasaki 650r, the signals though are quite small so unsure how other drivers would see it as. Did need a hyper flash resistor since it was gonna crazy like I was at a EDC concert. Fixed the problem, overall I’m pretty satisfied!
Brittany D
2025-05-04 14:31:38
First off, the box was not even packaged. It came to my house in the original product box, and the box wasn't taped or anything. I'm honestly surprised that it made it to me. The wires for the license are too small to do anything with. I've honestly never seen wires that small. So finally after wiring everything up, I went to mount it to the bike only to find out that it came with no nuts, bolts, or anything to mount it. Instructions say to use the factory screws, but the factory screws thread into the tail assembly that I'm taking off, so how am I supposed to mount it without proper hardware. So after 2 hours of doing wiring, and tearing down my bike, I had to put all the factory parts back on so that I could ride
Yvonne B
2025-04-25 11:57:02
The license plate holder is good, be sure to tighten EVERYTHING though, I didn't and almost lost the whole unit, luckily all I ended up losing was a turn signal and one of the brackets to hold it, I contacted support and they replaced the WHOLE unit, kinda insane to me that they did this but I was super happy to say the least, if I break mine somehow which is super unlikely, I have a replacement waiting for me
Will
2025-03-07 16:11:44
The tail tidy bracket isn’t wide enough for my small motorcycle.
Brendan D.
2024-12-19 17:18:28
I looked up what bikes this product was not compatible with and my bike was not on the list. So i purchased this product. I installed the turn signal lights and they worked for a day and then all of a sudden all four lights are flashing all the time when my indicator is on. If you own a gs500f suzuki, this product will not work.
Client d'
2024-12-13 11:16:34
N’éclaire pas assez selon les véhicules qui nous suivent. Difficile à distinguer. Donc non sécuritaire
Recommended Products