Your cart is empty.
Your cart is empty.Product Description
X3 Release Belt Cover Tool- Quick release SXS belt cover
--This quick release belt cover kit allows you to remove your clutch cover trail side without any tools
--The pins and lanyards will hold your cover on tightly. Lanyards will hold clips, so the hardware will not be lost in the dirt during the belt change
- Compatible with Can Am Macverick X3 2017-2023 All Models
Package Included:
--11 pins
--11 lanyards
--11 Black rivets
--11 Washers
--11 clips
Why you buy Clutch Cover Pin Kit Easy Belt?
The quick-release clutch cover pins are a wise investment
This kit once installed allows you to remove your clutch cover trail side without any tools.
Simply, remove the cotter pin and remove your clutch housing
Justin L
2025-08-31 13:39:59
These make changing the belt on the trail or in the dunes so much quicker. Dealing with the factory bolts is a PITA. Install can kinda be tricky getting everything to line up but these are definitely a must have next to a quick change belt tool.
Chris woods
2025-08-20 16:19:03
They should come with these from the factory race, changing the belt out riding really easy no tools necessary to get the belt cover off
GN
2025-07-29 21:41:41
I wish it came with type of install tool to help tight them. I used a small screw driver to place in the small hole of the screw to tighten them in. I think it needs a washer between the cover and the pin to help seal better so water don't get in. Other then that not to bad to install and rivet the on the cover.Fits well on 2020 Canam X3 RS Turbo
JustinB
2025-07-23 17:34:03
I’m on the fence about this. I installed all pieces and am having trouble getting the cover to fit tight enough to seal out water. If I screw the pins in enough for a tight seal, the cotter pins are near impossible to get in without extreme force. My current answer to this is leaving four of the old screws tightly installed in strategic places to suck the cover in enough for the pins to work everywhere else. Not perfect, but at least it’s only 4 screws to remove instead of 20 (or however many there normally are). I’d probably still buy this again, I’m just not thrilled with it. Plus it seems overpriced still.
Russell Palmer
2025-07-16 11:14:15
I like the kit it’s really cool. Should have came with a tool but I’m kinda handy so I made one myself. Otherwise it’s awesome.
stuart hess
2025-06-24 14:44:29
These do not thread in.
RC
2025-06-16 10:16:33
First off there are no instructions. Granted if you buy this set you already know you are at least slightly mechanically inclined enough to figure it out or know someone who is. Next description says black rivets which cool they will blend in but they are not black. I ended up using a 4.0 rivet and larger washers because the ones sent seemed so danty. If you don't own a rivet gun buy or borrow one they are same price as this set for a cheap one. The WORST part of this set is trying to screw the pins into clutch housing. I started by just using Allen wrenches to turn til tight. Then put clutch cover back on but pins were still really far out tried tightening more with Allen wrenches after breaking two smashing my knuckles I ended up drilling through a socket and cut an Allen wrench to fit in as a key (see attached pic of set up in use) with clutch cover on I used set up to tighten as much as I could then removed cover and had to use set to make 1 full turn on each to make sure cover would hold tight and seal properly. Right after I messaged a friend I ride with he said another person we ride with has tried these and they ended up loosening up and letting water and dirt into housing. I don't feel like I'll have that problem being my cover is pretty snug but it was a task to do so with no tool or instructions on how to. Just gotta wing it.
alisa carlson
2025-05-29 11:23:18
Quick disconnects for a belt incase of a disaster in a crunch, I’d recommend the aluminum cover that goes inside the belt housing as you’ll tare through the plastic shield without it.
KARINE ROBERGE
2025-05-15 15:54:07
Pas encore installé mais l'ensemble semble être correcte.
Justin L
2025-05-09 17:49:39
These make changing the belt on the trail or in the dunes so much quicker. Dealing with the factory bolts is a PITA. Install can kinda be tricky getting everything to line up but these are definitely a must have next to a quick change belt tool.
Chris woods
2025-04-25 14:43:31
They should come with these from the factory race, changing the belt out riding really easy no tools necessary to get the belt cover off
GN
2025-04-19 16:10:26
I wish it came with type of install tool to help tight them. I used a small screw driver to place in the small hole of the screw to tighten them in. I think it needs a washer between the cover and the pin to help seal better so water don't get in. Other then that not to bad to install and rivet the on the cover.Fits well on 2020 Canam X3 RS Turbo
JustinB
2025-03-31 13:36:10
I’m on the fence about this. I installed all pieces and am having trouble getting the cover to fit tight enough to seal out water. If I screw the pins in enough for a tight seal, the cotter pins are near impossible to get in without extreme force. My current answer to this is leaving four of the old screws tightly installed in strategic places to suck the cover in enough for the pins to work everywhere else. Not perfect, but at least it’s only 4 screws to remove instead of 20 (or however many there normally are). I’d probably still buy this again, I’m just not thrilled with it. Plus it seems overpriced still.
Russell Palmer
2025-02-23 10:06:33
I like the kit it’s really cool. Should have came with a tool but I’m kinda handy so I made one myself. Otherwise it’s awesome.
stuart hess
2025-02-16 18:01:08
These do not thread in.
RC
2025-02-15 18:41:10
First off there are no instructions. Granted if you buy this set you already know you are at least slightly mechanically inclined enough to figure it out or know someone who is. Next description says black rivets which cool they will blend in but they are not black. I ended up using a 4.0 rivet and larger washers because the ones sent seemed so danty. If you don't own a rivet gun buy or borrow one they are same price as this set for a cheap one. The WORST part of this set is trying to screw the pins into clutch housing. I started by just using Allen wrenches to turn til tight. Then put clutch cover back on but pins were still really far out tried tightening more with Allen wrenches after breaking two smashing my knuckles I ended up drilling through a socket and cut an Allen wrench to fit in as a key (see attached pic of set up in use) with clutch cover on I used set up to tighten as much as I could then removed cover and had to use set to make 1 full turn on each to make sure cover would hold tight and seal properly. Right after I messaged a friend I ride with he said another person we ride with has tried these and they ended up loosening up and letting water and dirt into housing. I don't feel like I'll have that problem being my cover is pretty snug but it was a task to do so with no tool or instructions on how to. Just gotta wing it.
alisa carlson
2024-12-22 13:02:10
Quick disconnects for a belt incase of a disaster in a crunch, I’d recommend the aluminum cover that goes inside the belt housing as you’ll tare through the plastic shield without it.
KARINE ROBERGE
2024-11-19 16:57:10
Pas encore installé mais l'ensemble semble être correcte.
Recommended Products
$24.41
$ 10 .99 $10.99