Your cart is empty.
Your cart is empty. The Adaptive Cutting System Plunge-Cut Track Saw offers powerful, precise track saw cutting performance. The saw pairs with the 62" Guide Track to create a versatile, capable track saw that delivers straight, smooth, splinter-free cuts in solid wood, plywood, and other sheet goods. The Plunge Saw comes with a 48-tooth carbide-tipped blade that is fully shrouded and retracts completely when not in use. A riving knife, which also retracts completely, follows the blade to keep the saw kerf open to essentially eliminate kickback risk, while a selectable anti-kickback switch prevents the saw from moving backward on the track when engaged.
The powerful 12-amp, 120V motor ensures that the saw can easily handle any sheet goods and even thick hardwoods - up to a maximum 2-1/8" cutting-depth. Bevel-cutting capacity can be set from -1° to 47° and can cut up to 1-1/2" deep at 45°. The blade-left design is optimized for right-handed users, and provides superior cutting visibility and control. An included dust port and bag collect chips to minimize cutting mess and provide the ability to connect to a vacuum hose.
Krisla Berreth
2025-08-12 12:41:59
I am very happy with this saw at a dramatically cheaper price then a Festool. It cuts very nicely and has no problem cutting 2 inch thick walnut or bubinga. Cuts are very nice with the included blade and with the sliding channel you get very accurate cuts. I covered the blade access with tape to improve the dust collection. With the blade access covered you get very good dust control when attached to a separate vacuum. I had no problem attaching the hose from my shop vacuum, it fit right into the port that came with the saw. However, the fit will depend on the vacuum you have so it is possible you may need to buy an adapter.
Josean
2025-07-31 14:24:45
I recently retook an old hobby with woodworking, and this Kreg saw along with its companion multi functional table were the first things I purchased.This saw has plenty of power to cut through 3/4†panel (thickest I’ve cut so far). It is important to keep in mind that when doing crosscuts, the wood can easily chip or split… my recommendation is to use painter’s tape and draw a cut line on top of the tape to guide you and to prevent the wood from splitting.The splinter guard helps, but is not 100% effective, so you still get some splinters, hence my recommendation earlier.The dust port is very effective especially if you attach a vacuum. Through the last couple of months I’ve been using this saw, I estimate an 80 - 90% dust capture by attaching a vacuum. For anyone starting out, this means there’s less fine dust particles in the air, which reduces the risk of breathing those into your lungs (which can lead over time to breathing issues).Other things I like are how well the saw works with the Kreg track, you can easily adjust the saw with the guide to virtually eliminate any play, thus allowing you to make very precise cuts.Setting the plunge depth is easy, and the saw’s handle allows for push or pull, so if you’re like me (5’ 10â€) or shorter, you can start your cut on one side, pause and go around to finish the cut without leaving marks.Hope this helps
Samantha
2025-07-17 16:27:08
Ordered this for my husband per his request. He used it to trim a little off the edge of new doors he installed at our house rather than put in all new prehung doors. He was able to trim the smallest amount using this with the same brand track system. Very happy with it!
Susan W.
2025-05-31 11:56:59
It works well and makes very clean cuts. Only complaint is that the dust control did not work well as shipped. I added an aftermarket cap to cover the arbor hole, and it works much better.
Tracy Lambert
2025-05-21 14:53:30
So I'm an older woman who has just recently gotten into woodworking. For my first few projects, I had to get my husband to cut the 4' X 8' sheets of plywood for me. Now, with this awesome saw and the track guide, all my husband does is carry the heavy sheets and places them on my workarea and I can cut to my hearts desire. I use it for SO much! Just LOVE this tool!
JCM
2025-03-17 16:00:00
Once you get the hang of positioning the track on the workpiece, it is an absolute joy to use. Most of the time, you do not deed to clamp the track in place because the sticky pads on the bottom do their job very well. I use a sheet of 3/4" insulating foam as a backer and just do sheetgoods cuts on the floor of my garage. The track is too short for ripping a 4x8 sheet the long way and a little too long for shorter crosscuts, but since I only have a small DW745 table saw, this gets used more than I thought it would. One tip: If you need to cut such that the track is not fully supported by the workpiece, use some scrap to hold up the side that is not resting on what it is you are cutting so that the whole track is parallel to the cutting surface. It takes a little time to catch on, but it works great.Did I mention that the cuts are super smooth? Better than any saw I have ever used. I love it.
Reviewer
2025-01-28 16:07:46
Fits the track perfectly. I like that it's plunge style and cuts with very little tear out. I would definitely get this again.
Bob Guardino
2024-11-24 14:24:51
I am very happy with the saw. I was concerned that the dust collection was adequate, but the dust catcher works. You may need to buy the custom connector to connect it to your shopvac, but I did not find it necessary. I am happy with the dust catcher that comes with the saw. For the price, it may be the best track-saw on the market.
Recommended Products
$198.95
$ 80 .99 $80.99
$89.99
$ 43 .99 $43.99
$519.00
$ 99 .00 $99.00