Your cart is empty.
Your cart is empty.A stout tool to remove and install plastic fuel tank lock rings from 4 inches to 7-1/4 inches without damage. Channel design on body allows the legs to adjust to fit a wide range of applications and keeps the drive centered. Works on the new smaller GM serrated rings and traditional rings. The design is compact so the tool is not left hanging over the work area with the potential for hitting other components. Also works on some Subaru plastic rings.
Big-D
2025-08-31 10:01:37
I do 99% of my own work on all of my vehicles, including replacing a fuel pump when necessary. This wrench is a must-have to work on fuel pump replacement and it will fit on many different type of cars where the fuel pump is located inside the fuel tank. That pump is mounted inside the tank and is covered with a access lid that requires this special tool to get the lid off. Any time you work with a fuel tank, empty of not, extreme care must be taken to avoid a very serious mistake, fire or explosion. Getting the protective lid off is tough and without this special tool, can be very dangerous. I like this tool because its adjustable to fit any make or model so you are not buying some very expensive tools that you may only use once in your life. This wrench adapts to any brand or style of fuel pump lid, making removing it a pretty simple process. Well worth the money I paid, although it was not very much considering how much dealerships charge for a model specific wrench. This wrench works great.Caution: Usually the fuel tank around the location of the fuel pump will have a rubber like coating on it to prevent anything causing a spark. I would suggest not wearing any nylon clothing or shoes that could create a static spark situation. Usually when removing the fuel tank lid, you have removed the rear seat and are in the car directly over the tank. Disconnect the battery also. Once the lid is off, fumes and raw gas are exposed. A simple spark could prove to be catastrophic. Also, it is highly suggested you NOT perform this procedure within your garage. Do so with all doors open and in the open air, this to allow clean air flow and circulation to allow gas fumes to exit the vehicle. And have a Fire Extinguisher close by, or better yet, have someone standing near by with a extinguisher at the ready just in case. Do Not take this procedure lightly, it is probably one of the most potentially dangerous maintenance functions you'll ever perform.
Jordan Zawodny
2025-08-10 16:46:50
Bought a cheapo model off Amazon that didn't work at all. This model was recommended on a forum and boy did it deliver instantly. I spent hours trying to get the fuel pump off with cheap techniques and a crummy tool. This removed it in 5 seconds.
DBot5000
2025-07-19 10:05:12
I was hoping to avoid buying the $180 Nissan Murano fuel tank cap tool by getting this instead. Bad call on my part. This tool only makes two points of contact instead of the eight the official tool makes. Getting the covers back on that vehicle with this will take an act of God.Otherwise it is very sturdy and adjustable, probably works great on most other vehicles.
David Deaven
2025-07-18 17:59:38
I used this tool to remove the ring on a 1998 Jeep TJ fuel tank. The fingers on the tool are designed so that they tighten against the entire length of the ribs on the ring, which means that you can really apply torque without fear of stripping the nylon ribs. In my case, the ring was frozen on so tightly that I ended up using an impact wrench to loosen it. Here again the tool has a good design, the central hexagonal head can be used with any socket tool, breaker bar, or as I did, impact tool. You are not limited to a handle on the tool itself.Getting the ring back on was also more difficult than I thought it would be since the fuel module on my tank is spring-loaded and the nylon threads can flex without fully engaging. This tool can be tightened on one side, then loosened on the other, allowing a nice way to move the ring by hand (using just the tool), while applying pressure at the part of the ring that has not yet engaged the threads.
Jeff Nuedling
2025-07-15 16:26:09
Good quality tool works good
Robert Holmes
2025-04-16 16:46:28
Very easy to use just make sure you retighten it after adjusting it.
Customer
2025-04-02 12:44:48
I got this to remove the ring on a 2007 Corolla. The ridges that this tool hooks to were not real big.I ended up ordering Toyota part 77144-04010 from Amazon and taking a hack saw blade at an angle and cutting the ring enough to pop it open with a screwdriver at about the 1 'o clock point if you look down on it. It unwrapped and about the 3-4 'o clock position revealed the problem: a piece of thread in the old ring had broken loose and jammed in the threads there. There was no way that ring would turn.I have no way of knowing if it would have worked on a non broken ring, but it seemed OK otherwise.I did pull the wing nuts and put on regular nuts as I had to try lots of torque, but it did not turn.
Mike B
2025-03-05 10:40:38
I used this tool to remove both fuel sender unit and fuel pump unit on a 2006 bmw e90 325xi this tool made life much easier to remove that lock ring which is secured tightly. The tool is sturdy and easy to use also great price
motoranchan
2025-02-15 18:49:14
ルノーセニックã«ä½¿ã„ã¾ã—ãŸãŒã€ã»ã¨ã‚“ã©å½¹ã«ç«‹ã¡ã¾ã›ã‚“ã§ã—ãŸã€‚力を入れã¦å›žãã†ã¨ã™ã‚‹ã¨ã€å›ºå®šã—ã¦ã„ã‚‹ãƒã‚¸ãŒå¤–ã‚Œã¦ã—ã¾ã„ã¾ã™ã€‚汎用ãŒé€†ã«ä½¿ãˆãªããªã£ã¦ã—ã¾ã£ã¦ã„ã‚‹ã¨æ€ã„ã¾ã™ã€‚
Normand
2025-01-14 12:11:38
Bueno
somo Thokchom
2024-12-29 15:27:00
Reputed product from reputed seller.
Rob
2024-12-20 15:17:45
This works well on a 1994 Toyota Supra.
zozapan
2024-12-14 14:02:17
Look’s like good quality but too pricey at $60.75 CAD.
Recommended Products
