Your cart is empty.
Your cart is empty.Lokar 2-1/4 inch Column Shift Linkage for GM Aftermarket is the ultimate answer to interference issues when you are unable to use factory or Lokar's hard column linkage. The cable allows you to route the cable around transmission, exhaust, cross-members and brake pedals. The Exclusive Billet Aluminum Mounting Arm can be used on either side of the column. Lokar's Column Cable Shift kit allows you to use the shift indicator kits. It can also be used in conjunction with the Back-Up Light or Neutral Safety Switch kit (BL-1400U) for most GM transmissions. It is available in black housing, designed with a specially extruded liner for extended life of the cable, and stainless inner wire measuring 6 feet in length. It has ready-to-install hardware and brackets included in the kit. There is no cutting or measuring as it simply bolts on. Longer cables are available upon request.
copterdok
2025-08-03 13:22:01
I needed a system to convert my 1972 Triumph Stag automatic transmission shifter to the TH350 Street Fighter transmission that I installed. This kit worked very well. It has all the brackets and hardware that I required with only minor changes and engineering to fit it onto a British car.
Laura Dahl
2025-07-18 20:07:21
Good quality.... However- the cable is TOO short! Unable to use..... :( Wish I could trade the shorter (72" cable for the 120" cable)...
Chief
2025-07-13 14:56:39
I was using it on my 50 Chevy project. Could not get it adjusted so that it would shift through all the gears on my 4L65. Switched to a floor mount & it worked out perfectly.
Brandon in California
2025-07-11 14:24:44
This thing fits and works perfect for anyone doing a 5.9 cummins with a auto tranny into a 1970s ford truck. Almost like it was meant to be for this application.
Johnny B.
2025-06-19 11:34:11
There is about 1/4 space left the 2 inc MAY fit perfect
Juan Perez
2025-05-27 18:24:46
Amazon showed it fit my 78 K20 however the steering column is too skinny for the bracket.Also my selector lever was curved not flat like the instructions showed.
Tom Spencer
2025-05-25 14:37:23
Picked up for a street rod build and works perfectly
copterdok
2025-05-19 17:41:19
I needed a system to convert my 1972 Triumph Stag automatic transmission shifter to the TH350 Street Fighter transmission that I installed. This kit worked very well. It has all the brackets and hardware that I required with only minor changes and engineering to fit it onto a British car.
Laura Dahl
2025-05-01 15:32:02
Good quality.... However- the cable is TOO short! Unable to use..... :( Wish I could trade the shorter (72" cable for the 120" cable)...
Chief
2025-03-22 13:14:52
I was using it on my 50 Chevy project. Could not get it adjusted so that it would shift through all the gears on my 4L65. Switched to a floor mount & it worked out perfectly.
Brandon in California
2025-03-11 09:26:33
This thing fits and works perfect for anyone doing a 5.9 cummins with a auto tranny into a 1970s ford truck. Almost like it was meant to be for this application.
Johnny B.
2025-02-20 13:49:16
There is about 1/4 space left the 2 inc MAY fit perfect
Juan Perez
2025-01-27 16:18:59
Amazon showed it fit my 78 K20 however the steering column is too skinny for the bracket.Also my selector lever was curved not flat like the instructions showed.
Tom Spencer
2024-11-30 11:08:54
Picked up for a street rod build and works perfectly
Recommended Products
$71.09
$ 30 .99 $30.99