Your cart is empty.
Your cart is empty. Type:Piezoelectric tweeter ultrasonic horn
Housing material:ABS
Size: Approx. 38 X12.4 mm
Rated voltage: 10 Vp-p
Frequency range: 10-50 kHz
Min. sound output:90dB(at 10cm at 40khz)
Operating temperature: - 20 -70 Centigrade
Easy to install,propagation distance,good performance.
Waterproof, strong sound pressure,good consistency.
Note:
manual measurement, there is a small reasonable error range.
Ex-ChiefJim
September 5, 2025
I hooked these up to an adjustable ultrasonic generator and 3D printed an enclosure. These two speakers are responsive to the ultrasonic sound generator and help us to quite down the neighbor's barking dog. They handle the volume and output just fine and have made it through spring rains and summer sun without issue.
dsrtrt
August 17, 2025
I replaced a bad speaker in my mouse blocker device with this exact speaker and mouse blocker works great again. Sound quality is back to oem quality saving me from having to spend 100 dollars for a new device
Quintin Z Warner
August 14, 2025
Used to replace drivers in a community double driver horn and they didn't last 5 minutes
Dan kechter
August 3, 2025
These seem durable
Godzilla62
June 12, 2025
These are loud at 5 volts. 4000hz made my ears hurt. They draw about 10ma so 2 can be hooked up to the tone pin on Arduino. Pest, animal repeller that you know that generates ultrasonic waves. Although I've seen these spec'd at 10v that much is not needed. Many repellers sold on line do not work or have insufficient volume.There is some sympathetic frequency generated at 31khz, but not bad to my old ears, but may bother others. *Edit 3/27/22 I added a 1k resistor in series to the + side of the speaker and it is now completely silent.Code : for variable frequency on Arduino 22khz to 42khz/* Varible Frequency Output From Godzilla */int speaker = 9; /* Pin 9 */unsigned int sfrequency = 22000;unsigned int efrequency =42000;void setup(){ pinMode(speaker, OUTPUT);}void loop(){ for (unsigned int i = sfrequency; i tone(speaker, i); delay(2000); /* 2 Seconds */ }}
Robert
June 4, 2025
The only disadvantage is the positive and ground are not marked. No simplest of instructions are included. I had only the online photo from amazon to go off of.
ALAN ROSS
June 2, 2025
Ultrasonic testing from a generator. I was doing an experiment to see if these could work for the test. Homemade pest control. They have a wide resonant frequency response unlike certain piezoelectric elements. Both audible and in audible.
Jon l.
May 22, 2025
Speaker's are great they do just what they said they'd do.shipping thru u.p.s on the other hand was terrible like usuall . Product was sent to 3 different compass points none of which helped the delivery process.
Lou
May 7, 2025
Received used speakers. Came with free solder, copper wire and some electrical tape. Speaker tested damaged with a multimeter.
Ex-ChiefJim
April 28, 2025
I hooked these up to an adjustable ultrasonic generator and 3D printed an enclosure. These two speakers are responsive to the ultrasonic sound generator and help us to quite down the neighbor's barking dog. They handle the volume and output just fine and have made it through spring rains and summer sun without issue.
dsrtrt
April 24, 2025
I replaced a bad speaker in my mouse blocker device with this exact speaker and mouse blocker works great again. Sound quality is back to oem quality saving me from having to spend 100 dollars for a new device
Quintin Z Warner
April 22, 2025
Used to replace drivers in a community double driver horn and they didn't last 5 minutes
Dan kechter
April 3, 2025
These seem durable
Godzilla62
April 2, 2025
These are loud at 5 volts. 4000hz made my ears hurt. They draw about 10ma so 2 can be hooked up to the tone pin on Arduino. Pest, animal repeller that you know that generates ultrasonic waves. Although I've seen these spec'd at 10v that much is not needed. Many repellers sold on line do not work or have insufficient volume.There is some sympathetic frequency generated at 31khz, but not bad to my old ears, but may bother others. *Edit 3/27/22 I added a 1k resistor in series to the + side of the speaker and it is now completely silent.Code : for variable frequency on Arduino 22khz to 42khz/* Varible Frequency Output From Godzilla */int speaker = 9; /* Pin 9 */unsigned int sfrequency = 22000;unsigned int efrequency =42000;void setup(){ pinMode(speaker, OUTPUT);}void loop(){ for (unsigned int i = sfrequency; i tone(speaker, i); delay(2000); /* 2 Seconds */ }}
Robert
March 18, 2025
The only disadvantage is the positive and ground are not marked. No simplest of instructions are included. I had only the online photo from amazon to go off of.
ALAN ROSS
March 13, 2025
Ultrasonic testing from a generator. I was doing an experiment to see if these could work for the test. Homemade pest control. They have a wide resonant frequency response unlike certain piezoelectric elements. Both audible and in audible.
Jon l.
January 25, 2025
Speaker's are great they do just what they said they'd do.shipping thru u.p.s on the other hand was terrible like usuall . Product was sent to 3 different compass points none of which helped the delivery process.
Lou
January 1, 2025
Received used speakers. Came with free solder, copper wire and some electrical tape. Speaker tested damaged with a multimeter.
Recommended Products
$33.99
$ 16 .99 $16.99