Shopping Cart

Your cart is empty.

Your cart is empty.

MENSI 11.8” Long Propane Push Button Piezo Igniter Kit Gas Grill/Range/Heater/Stove Spaker Generator Ignition Set 2Pcs/Lot

Free shipping on orders over $29.99

$9.99

$ 4 .99 $4.99

In Stock

About this item

  • DIY kit suitable for all Propane & Natural Gas Gears but you may need do some modification during installation, It not fits all the current hole for install or the length of wire (if power is not enough you can use two)
  • Output voltage: >=20kv,Sparking distance: 3-5mm, wire length 30cm, Electrode : M10*1 length: 57mm
  • No battery needed just press, one press one spark but 𝐌𝐚𝐤𝐞 𝐬𝐮𝐫𝐞 𝐲𝐨𝐮 𝐜𝐨𝐧𝐧𝐞𝐜𝐭 𝐭𝐡𝐞 𝐠𝐫𝐨𝐮𝐝 𝐰𝐢𝐫𝐞 𝐨𝐫 𝐭𝐨𝐮𝐜𝐡 𝐠𝐫𝐨𝐮𝐝𝐢𝐧𝐠 𝐩𝐨𝐢𝐧𝐭𝐬. Life time: Over 30000times
  • Installtion Tips: VERY IMPORTANT!!! - 𝐭𝐡𝐞 𝐩𝐢𝐞𝐳𝐨 𝐢𝐠𝐧𝐢𝐭𝐞𝐫 𝐡𝐚𝐬 𝐚 𝐬𝐢𝐥𝐯𝐞𝐫 𝐬𝐢𝐧𝐠𝐥𝐞 𝐥𝐢𝐧𝐞 𝐰𝐡𝐢𝐜𝐡 𝐚𝐜𝐭 𝐚𝐬 𝐠𝐫𝐨𝐮𝐧𝐝 𝐜𝐨𝐧𝐧𝐞𝐜𝐭𝐢𝐨𝐧 𝐩𝐨𝐢𝐧𝐭. you must tough that point to a metal control pannel or add some metal to get a singnal there so you can get it correct spark. Without Connect well, The igniter cannot ignite the burner because the spark will not come from the head of electrode pin
  • Pin straight length: 19.5mm 135degree at head 9.0mm



Product Description

universal

Piezo igniter Assembly Replacement Kit

Piezo igniter Assembly Kit

How to Install a Piezo Igniter Set on your Grill, Stove, Heater?

This igniter kit can be used for any home gas appliance or outdoor heaters just need do some small modifications.

* The drilling mounting hose of your stove grill is necessary before you want to install this kit if your stove do not have current hole to insert the piezo.

* The electrode wire cable just 30cm long, so make sure it fits the installation position before ordering.

* The igniter cannot work if you do not connect the ground point to the plate of grill or connect ground wire.

The Ground Point is a Not A Terminal or Cable

The right picture show the ground connection line. Normally it installed on a metal plate of your grill, heater.

But if you do not have metal plate on your project, you can attach a metal piece or try to connect a cable to ground as well in this part.

So the igniter will work properly.

It can be worked for natural gas or propane.

Piezo igniter may need several times to push to ignite gas.


Joe
2025-08-24 18:27:38
I had a battery pizzo starter on a propane heater and had to change batteries often so i installed this manual one. It was plug and play- the wire from the first fit the receiver on this product. Worked great.
SIMTECH
2025-07-12 16:23:36
Used this to update an old heater and it worked great, just took time to get the location and spark gap worked out. Since you get two the second will go on another project.
Douglas Cummins
2025-07-11 16:50:41
good price, I'd buy again
Candice
2025-05-19 14:02:02
Had a propain outdoor heater that needed a new one and this worked perfectly!!!
Paul Christiansen
2025-05-08 20:01:27
No more fooling with a battery. Easy installation and has considerable adjustment ability to length to position ignitor over gas manifold. Had to bend tip of ignitor using needle nose plyers to get it closer to manifold. Now ignites on first or second push of the button.
Brian D
2025-04-18 16:41:38
Failed to light after three weeks.
Cessna Guru
2025-04-10 16:13:06
When I converted my BBQ to Natural Gas from propane my flawless working LP piezo igniter did not work as NG is much harder to ignite than LP. After positioning this replacement igniter, advertised to work with NG several different places in and around the stream of NG, it simply does not work. The instructions are that the base of the igniter (not the button switch) needs to be grounded (although they say it in an obtuse way) to the metal housing of the appliance. Well if you are in contact with the housing (knee other hand, etc.) and push the button prepare for a 20kv shock (not fun). Likely this is not a UL or CE certified device and should not be sold.
JimInAlabama
2025-04-08 12:57:44
I got this for our Outland fire bowl and I'd buy it again but I'd install it differently. Underneath the firebowl there's a bottom cover. There's a round hole in that cover near the burner assembly, obviously there for an ignitor. So I drilled out in the center of that existing hole and as you see in the other picture the business ignitor is too close to the edge of the burner. In my case it sparks across from the ceramic to the burner and works, not always on first click. I'm gonna leave it alone but if I had a do-over i'd pick a spot and drill from the top, probably on the opposite side of the burner tube. It was a pain but worth it.
ILARIN
2025-03-24 18:36:03
Fanno la loro funzione egregiamente
tam123
2025-03-05 12:20:15
One ignighter not sending spark to sparkers and both sparkers sparking at base and not at tip I still have one red button ignitor in machine its a lot of work to remove it so can you charge me for that and I'll return the other 3 peices or do you need all four returned please advise
Leonardo Gabriel Palacio Padrón
2025-03-02 13:31:37
Genial
Jimmy
2025-02-21 17:09:52
Fungerar dåligt
Generic consumer
2025-01-01 14:29:10
Used it to replace the electronic one (junk) on my 1 year old bbq that only lasted about 6 uses.Works every time. Has already outlasted the original.I would buy this again, but there were two in the pack so I expect they will outlast the bbq anyway.
Recommended Products