Your cart is empty.
Your cart is empty.Enjoy the RC Fun with MEUS Racing!
Customer
2025-07-22 10:40:07
Solid driveshafts. I got these because I stretched the wheelbase of my capra and the worked great for what I needed
J.C. NOR-CAL AMERICAN BULLIES
2025-07-19 11:59:48
All good. Smooth operator
Claybats theSane
2025-05-25 18:00:42
UPDATE: Seller noticed I had issue with first set and replaced them. The new set does not have the issue with the internal catches. It rotates smoothly and appears to work well. Thank you for noticing I had an issue and making corrections.The heads catch on internal burrs causing stiffness in movement. Rotation is not smooth for either of the two shafts included in the package. Also, the drive shaft yoke rubs against one of the center yoke ears limiting the angle at which this can be used. Splines go all the way down the slip shaft, so that is good. I fully expect the internal friction on the pins in these balls to overheat them and destroy them in a short amount of time.
Joe C
2025-04-26 12:13:55
UPDATE: 12/5/24 - I've updated the review from 2 stars. MEUS Racing reached out to inform me that the phasing problem was a manufacturing issue and offered me a full refund/replacement. The interaction was the best customer service experience I've had in a long time.I ordered the 94mm version and the overall length is 100mm. This was the right length for my SCX10 III Base Camp with dig conversion. The look great and are very well made except for one big problem. They can't be phased properly. No matter how I clocked the ends the U-Joints never lined up properly. This caused a noise and vibration at any speed above a slow crawl. One is worse than the other. I've had good experiences with MEUS parts before, so I wasn't expecting to have problems with these driveshafts. I'm not sure if they are all like this or if I got a bad set, but I ended up just rebuilding my stock driveshafts and returning these.
Laura
2025-03-07 11:42:00
These driveshafts are much more durable than the factory plastic ones that come with these vehicles. With a heavier weight that factory parts, it keeps the vehicle much lower and distributes weight much better. When I first received these driveshafts, I had some install issues when I put them on my vehicle. The paint that was applied to the driveshafts ended up in the thread hole where the small set screw is installed. It ended up stripping out the set screw and rendering my vehicle useless until extracted.Upon extracting the stripped out setscrew, the driveshaft is then damaged, and the pinion that it goes through ended up damaged. I contacted the company, who promptly responded. Within a few messages, we had fixed a small quality concern that is now remedied on newly produced parts. They also sent me out a new set of driveshafts, new set screws, and a new pinion shaft to replaced my damaged one.The new set of driveshafts worked like a charm, no paint stuck in the threads, and easily installed. The new pinion shaft fit right into my TRX4, and off again I was romping through the yards. Great product, easy resolution to my issues, and worked out perfectly! Would buy again from this company.
Marcus Darpino
2025-02-23 09:22:04
This is a great price for a great product. MEUS delivers every...single...time.
Jessica M
2025-01-29 16:17:34
I used this to replace the drive shaft on a TRX4 and they were a perfect fit. They seem to be made well and I haven't had any problems with them.
J&K
2025-01-10 17:43:56
Great set of driveshafts for 1/10 scale rc cars. They fit perfectly & seem very durable!! They look good & are holding up well to regular use.
Steve-O
2024-12-28 12:57:51
Superb quality , quick efficient delivery, really nice product good fit
Recommended Products
