Your cart is empty.
Your cart is empty.PSO
2025-08-09 15:44:37
Perfect fit gave a super beautiful look to my pickup.
steven r
2025-08-06 18:03:04
CON: Adjuster screws. Install not as easy as it seems. PRO: Good replacements for my 20YR old OEM.TAKE a good look at how the NILIGHTS are assembled as the closely resemble the stock ones you're about to remove.Use a 15mm socket to remove a diagonal bumper brace, 2 bolts by the Light and one on the end of bumper (3 total). This will drop the lower facia down enough to get the light bracket out/in. Remove the light socket. Completely remove the headlights (2 pins) and the Marker/Running light assemblies for access to the top of the Fog light bracket screws.I found it easiest to completely disassemble the Fog lights for removal and install. Completely back the adjuster screw out (OE is ALLAN Wrench. NILIGHT is PHILLIPS). Use a flat screwdriver and hand strength to pop the light assembly out of the bracket. Now a 10mm ratchet wrench(or 1/4 drive w/10mm socket) to remove the bracket screws from top where the other light assemblies were removed.REVERSE order with new assemblies. I used SEALIGHT YELLOW H10 LED in my new fogs.GOOD LUCK
m4sworks
2025-07-08 17:50:40
I put many miles on my truck. So this is my third replacement from cracked lenses.These housings are as good a OEM !
Mrscllc
2025-05-05 15:26:41
Great fit in my 2006 GMC Sierra 1500 z71. The installation was straightforward. I find the fog lights are super bright, they made me order new headlights so because I realized how dingy the headlights had become!
CW
2025-04-10 10:57:37
I recently replaced all the lights on my '03 Yukon, including the Fog Light Assemblies. It was a simple; unbolt the old and reattach the new. This assembly came with everything i needed for the replacement, including new light bulbs.
Cheeseman
2025-02-18 15:26:21
I’ve been using them because my other ones got all foggy from overtime, but these are good. I replaced the lightbulbs though with LED.
Customer
2025-01-28 15:11:44
Haven't installed yet looks new
Nord
2025-01-26 10:59:10
I bought these because my Chevy has the Chevy Fog-light Syndrome (fog-lights with broken glass), Nothing about this purchase was successful, absolutely NO OEM fitment of the brackets, the brackets were to low profiled compared to the GM originals and would not fit even closely to the screw mounts on the bumper, these new one end up to high and you cannot adjust the light enough to make it work, the light mounting to the bracket is up too high.To make these fit you will need to screw them directly on to the plastic on the bumper which is a royal pain in the @xx if you need to do it nice and neat from the inside. I was trying to attempt to use the old brackets, but the lights will not fit those brackets at all so you will either need to directly screw these in to the bumper either from the inside or outside through the plastic or find a different set of lights that has a direct fitment because these DO NOT fit my Chevy Tahoe 2001.After some tweaks to finally get them placed I noticed they don't even work, and yes I did check fuses and relays and they were not at fault here. I am hugely disappointed and I cannot recommend trying these.Right now they are installed just for esthetics to make the car look better, but is not functioning and I have ordered a replacement to see if the new one at least will light up, they will still not fit but at least I made it look better.I didn't have high expectations from the beginning in terms of great lighting or quality, (quality-wise they are very light and cheap feeling), I did however expect them to fit properly and at least light up.Look elsewhere or spend a few more bucks on lights with higher quality that might actually be an OEM fit.
Recommended Products