The media could not be loaded.

When I ordered these I had my doubts, BUT these are AWESOME!Though the instructions show them being fastened after it appears that the sheet is on the bed, I found them MUCH easier to put on by starting on the sheet at the top of the mattress & clipping one side to the top part of the sheet before even putting the sheet on the mattress, then slid the cord under the mattress at the same time I fitted the sheet on & then clipped the other side of the sheet on the side of the mattress once it had been stretched over the corner. From there you can adjust the tension so it makes the corner fit snug. By doing it this way, you don't have to lift the mattress to try and clip the top part of the sheet, so it's much easier on your back & faster too.I have satin sheets which ALL seem to be made for matresses' 3+ feet thick so as a result the fitted sheet is WAY too big & with one turn in the night, simply pulls right off my regular sized mattress taking the top sheet & blanket with it.Before finding these little gems, it was necessary to totally remake the bed from scratch on a daily basis as everything would end up in a big jumbled mess from the night before. NOW, it makes up like a normal bed, & I don't have to struggle trying to tuck sheets & blankets in over & over knowing they will pull loose the minute I get into bed! Not to mention that when I move or turn over, the sheets STAY PUT & I don't end up with tons of wrinkled up bottom sheet underneath me.Since satin sheets are so slippery, it also helped that I got a set of 4 Sheet Grippers for the top sheet. Between using the Bed Bands on the bottom & the Sheet Grippers on the lower section of the top sheet, I now sleep wrinkle free & ALL the covers stay on the bed the way they are SUPPOSED to!While the Bed Bands are SUPER EASY to install, a word of caution on the Sheet Grippers- these are EXTREMELY hard to put on if you have arthritis or any hand/wrist problems. Once they're on, they stay put & make the sheets do the same, however, be prepared to spend some time getting them on in the first place, & if you have serious hand/wrist issues, have a young person who does NOT have problems do it for you! ;-)Since sheet manufacturers seem to think we all sleep on triple thick matresses' and manufacture their sheets accordingly, the sheets simply do not fit the beds anymore & once that fitted bottom sheet gives way, the whole thing goes. All in all, these were one of the best purchases I have made in a while- if they work on satin sheets this well, I can imagine they would be just as effective on cotton sheets, so if you are having issues with your sheets slipping off your bed, give these a try- you will be wrinkle free!

BLUF, we've been successfully using these in combination with two other sheet holding devices for about the last week or so. I wish they were longer as we had to use them at full length (and consequently lost the functionality of the center adjuster) because they are securing a fitted sheet on a California king mattress.We've gotten tired of wrestling with non-fitted sheets on our California king waterbed for several years and recently replaced the waterbed mattress with a California king coil spring, reversible mattress from The Original Mattress Factory. This model (Orthopedic adjustable) fits tightly enough in the waterbed frame making it a major challenge to lift out and make/adjust the sheets -- but not tightly enough to hold the fitted sheet in place in the long run. We purchased sheets from Amazon (ASIN# B06X6MBV92) that we like and used these Bend Band grippers combined with SheetLock fasteners (B01N5SIATD) and Original Sheet Suspenders (B0014AMBWK), also from Amazon, to make the fitted sheet stay put.Since the fitted sheet would have been a pretty loose fit on our 10-1/2 inch tall mattress, we used these Bed Bands in each corner. The clips themselves held very well to our particular sheets (which are a bit slipperier than plain cotton) when we tested it by tugging on them once secured to a sheet. Because we had them adjusted at full length, the only way we could set the tension was based on how far away we clipped the second clip along the adjacent side of the corner. The elastic cords in these Bed Bands seems to have stronger tension than straps that we've used and I suspect the elasticity of these corner "cords" will outlast that in the straps we installed elsewhere on the mattress. We used the Original Sheet Suspenders in a cross-shaped pattern and the SheetLock fasteners across the shoulder and foot areas to complement the Bend Bands.Since our mattress has no pillow-top portion and no memory foam, it's a rather solid, firm surface and I'm impressed that the sheet is held in place very well by these Bed Bands along with the two other gripping products. I'm deducting one star because they don't seem to be long enough to place where they would singularly hold a Cal king sheet in place. I'm not really certain any single solution would work over the long run. That said, I think if these were used alone on a twin or full mattress, they might have more overall sheet tightening results.Finally, I would note that the user has to be practical in adjusting the tension on the bands -- on this or any other similar products. The more tension you put on the elastic, the more likely you'll experience the clips slipping off the sheet. I think most of the manufacturers know this and don't make the clips so tight that they are more likely to *tear* the sheet than to *slip off* the sheet. If you're looking for military cot type of super taut sheets permanently, put heavy duty tarp clips (ASIN# B01KTULL80) on the sheet, tie cords tightly between them, then drop the mattress in place. Be sure you don't have a reversible mattress because I suspect those clips will leave noticeable indentations on the bottom side of the mattress!

Very impressed with this product. I have always used clamps on my bed, my children's bed and I use them to hold on my tablecloth. I have bought so many different clamps over the year and they have all had failures whether it's the elasticity giving out or the metal clamps falling apart or them ripping what they're supposed to hold on to. I finally got sick of purchasing whatever was cheapest at the time and opted for the little bit more expensive option. It was so worth it. This is definitely one of the products where if you spend a little bit more money up front. It'll save you money in the long run because you won't have to constantly replace it. This product has earned a lifetime loyal customer and a well-deserved spot in my housewarming gift list.

My husband and I are so impressed with the quality of these 'pocket sheet' 'BED BANDS'. These BED BANDS are worth the weight in gold. The quality is impressive as my husband and I have Chronic pain and I'm disabled, needless to say we are not sound sleepers. We flop from side sleeping to sleep on our backs, the sheets had to be fixed once or twice a night without the 'BED BANDS'. The fitted sheet now stays for weeks at a time! My husband and I are impressed with this product!

These achieve their intended purpose and are well made. The clips have a good clamping force. The jaws of the clips are padded so they don’t rip the bed sheet over an extended period of use. Expensive compared to the Chinese varieties.

Finally something to stop my sheet from always coming off. Specially if you have a remote control bed

Does what I expected it to do. I was skeptical that it would keep my bedsheets from pulling out the corners but it holds them. I've had better nights sleep since.

Excellent prdouct. I've been using for almost 10 years and they still work great.Bought a different brand on Prime recently for another bed and they broke within a week!Just ordered two more of these ones as I know the quality is there.