Your cart is empty.
Your cart is empty.The multi-stream drip emitter is an ideal sprinkler for watering annuals in a flowerbed or container. The pattern is a full pattern gentle multi-stream that extends up to 3 feet at typical drip operating pressure of 30 PSI. You can decrease the spray radius, or even shut it all the way off, by rotating the multi-stream head clockwise. The 10-32 male thread (MT) inlet on the multi-stream emitter connects to an optional 6 or 12-inch drip stake with 10-32 female thread (FT). The inlet also has a barb for direct connection to 1/4-inch tubing and you can then hold the emitter in place at each plant with a drip tubing Y-anchor stake. You can either run 1/4-inch drip tubing from a drip manifold, a 1/2-inch drip tubing “lateral” line, or directly off the hose faucet with a 1/4-inch hose faucet x 1/4-inch adapter. Recommended operating pressure is 30 PSI. For outdoor irrigation use with cold water only.
Katie
2025-08-31 12:42:58
It is working well. Functional, long lasting.
GlennW
2025-08-28 20:23:43
I like these. They don't sun damage due to being black and opaque. Also the plastic is a little bit flexible which makes them more durable. My previous ones were cheaper plastic and the sprinkle tops got brittle and crumbled into little pieces form the sun. I'm in Arizona...
Tim
2025-07-01 21:45:09
I would say these are 4.5 stars, but Amazon doesn't allow half stars. I used these in my raise vegetable bed so I can adjust according to to the water needs of each crop. Of course water pressure plays a factor, but the spray distance is pretty good, and even. I really like that these emitters are on spikes. The spikes allow me to raise or sink them into the ground, which gives me control over the distance water is sprayed. Many vegetables don't like water on their leaves; it promotes fungus and mold growth. So, having the spikes and adjustable sprayer heads I can minimize water on the leaves. Since using these, I've had more success with my winter and summer crops. The only issue I had was 1 out of 5 had a loose head fitting, so twisting for greater water distance eventually resulted in the head flying off; thus spraying leaves and wasting water. Since it's plastic, there was no way to fix that. I painted it with an "x", and don't adjust that head.
Lisa P. Davis
2025-06-15 20:06:33
I like these little sprinklers! I ordered these--the information says two packages, but only one arrived. At first, I was worried because I had no correspondence to tell me that the other package would arrive later, so I sent an e-mail to them. Then I did a little digging and found that there is now a message saying that the other one will arrive in a few days. Oops. I am sorry I sent the message too quickly. But I already have some of these and I have really liked them, even though I agree with other reviewers that their name is a little misleading, as they are a little more like a sprayer than a dripper.
JSG
2025-05-28 18:36:02
I am really happy with the low cost and the performance of these emitters.
CA Buyer
2025-04-06 16:41:30
You can put the stake in the middle of the plant and adjust the spray valve to water just how much you want.
Nityamo L.
2025-03-24 10:57:19
The barb connector breaks off very easily
Lola Getsit
2025-03-04 10:28:39
These work great! Much better than the cheap ones I tried first that broke all the time. Definitely good value!
Customer
2025-01-31 18:09:42
Just what I needed and was looking for!
Hsc
2025-01-02 14:57:48
Had to re drill all the little holes as they were plugged with plastic
TSE
2024-12-11 12:24:42
Useless, not the bubblers. Get the bubblers.
Recommended Products
