Your cart is empty.
Your cart is empty. Electrical Specification：
Operating voltage range: 5-8.4 Volts
Operating speed at no load ( 5V ): 0.17 sec/60°
Operating speed at no load ( 7.4V ): 0.14 sec/60°
Operating speed at no load ( 8.4V ): 0.12 sec/60°
Stall torque at locked ( 5V ): 24.5kg.cm(340.2oz-in)
Stall torque at locked ( 7.4V ): 34kg.cm(472oz-in)
Stall torque at locked ( 8.4V ): 41kg.cm(569.3oz-in)
Stall current at locked ( 5V ): 2.1A
Stall current at locked ( 7.4V ): 3.2A
Stall current at locked ( 8.4V ): 3.9A
Idle current at stopped (5/7.4/8.4V): 4mA
Control Specification:
Control System: PWM (Pulse width modification)
Pulse width range: 500-2500μsec
Neutral position: 1500μsec
Running degree: 270° (when 500-2500μsec)
Dead band width: 3μsec
Operating frequency: 50-330Hz
Rotating direction: Counterclockwise (When 1500-2500μsec)
Product Specification:
Suitable for: for 1/8 1/10 1/12 Scale RC Cars, Trucks
Motor Type：3-pole(s)
Gear Type: Stainless Steel
Spline:25 Tooth
Gear ratio: 275
Bearing：Double Bearing
Waterproof Performance：IP67
Connector Wire: 17.7in (450mm)
Size: 1.57*0.79*1.59inch（40 * 20 * 38.5mm）
Weight: 2.11oz (60g)
CE /RoHs: Yes
Packing List:
2 x DS3235 35kg Servo （270°）
2 x 25T Adjustable Metal Servo Arm
2 x Accessories Set (As Shown on The Picture)
Tacosauce15
2025-08-26 11:25:26
Good servo. Should fit right in with a lightweight Minimax. metal gears durability is a plus. Speed is average. Fits Traxxas Servo saver. 25t
Daytona
2025-08-21 12:58:30
These really are a great value-cons: servo grommets are not very good,bit lazy on speed,servo arm screws suck- Pros: torque is really good -beefy aluminum servo arm and can take a pretty good beating-never had one fail yet- they work great-
KostyukZ
2025-08-12 16:20:21
Broke a servo on my RC car and bought this to replace it. I like how you get to so that if you mess up the servo a second time, you'll still have another one.
Jackal
2025-08-10 12:31:04
Purchased these for my danchee ridge rock crawler steering servos and what a improvement over the stock ones were only 6kg torque to the 25kg with out the servo savers used the aluminum arm with the last hole cut off and sanded smooth installed the ball link with 242 loctite and snapped the control arm back on and no stall time turning or delayed because of the servo saver turning response is fantastic now just need some wheel spacers to keep the tires from rubbing the four link. Great product would use them again.
Professor 2.0
2025-07-10 14:12:20
These servos are tuff and strong, I replaced my stock E-Revo 2.0 for a more robust metal gear servo that will handle hard core bashing. They have been holding up so far.
BudMor
2025-06-25 10:04:09
I have not had any problems to date with these servos and have order them a few times on here.
Customer
2025-06-15 17:13:37
Installed on my dual servo Emaxx...very strong!
Bob P
2025-06-04 12:44:20
Strong and fast speed
Kunde
2025-06-02 17:33:43
The media could not be loaded.
Scott Milne
2025-05-21 18:02:08
Installed in a Team Associated RC8. So far no issues at all. Seems to be a very strong quick servo. I will be buying more and using them in my other RC’s.
the bull
2025-03-19 11:20:23
Puts out good torque to steer your rig but does not spin so quick as others. It can handle some decent voltage. Good servo for cheap people who dream of a rich man's performance. I am that guy.
Daniel Johnson
2025-03-07 14:12:40
work very well in my RC sailboat.
MICHAEL
2025-02-13 11:09:32
Strong, high-quality, and reasonably priced. Would buy again.
Recommended Products
