Your cart is empty.
Your cart is empty.Product Description
ajee manual pipe bender, a helpful tool that meets your pipe-bending demands. This equipment, made of solid metal, can assure a longer lifespan. Much less labor is needed because of the longer handle. It can easily bend the pipes from 0 to 180 degrees.
Why Choose ajee ?
- Premium Tough Quality
- Incredibly Low Prices
- Fast & Secure Delivery
- 24/7 Attentive Service
Sturdy Steel Material
Humanized Design
Convenient to Use
1/2 inch Pipe O.D.
Specification
Pipe bender: aluminum alloy
handle: 45# steel
Not-slip handle cover: rubber
Elbow Specifications: 1/2 inch (length of tube OD)
Bending radius: 36.5mm
Bend Angle: 0 to Bend 180 degrees
Product size: 60*9*9cm/23.62''*3.54''*3.54"
Customer
August 13, 2025
I bought a handheld "plier" type bender that did several different diameter tubing, including 3/8" and it was a disaster, so I bought this bender. It's amazing! No comparison to the pliers. The bends are beautiful. It is a bit unwieldy and tends to flop all around, but it is a side effect of the tool design. The design works to give you very nice looking bends. It took a bit to learn how to get the tubing into the hook. It won't go straight in, you have to angle it a certain way. I was using steel 3/8 tubing for a transmission cooler I was adding to my truck. I'd say it came out pretty nice. Highly recommend.
farmer83
June 30, 2025
Used this to make a series of bends for 3/8" 0.035 wall stainless tubing. It worked great. Never had to do a 90 or 180 bend but i'm sure it would be easy to do.
Melissa Corey
June 27, 2025
Smooth bends and thin wall tubing bends well. Worth the money
Customer
June 26, 2025
3/8 stainless not a problem with this bender.
Jim In Idaho
May 20, 2025
Got this to bend 3/" mild steel tubing for attaching the mount points for the fiberglass body to the chassis for my race car. Works really well and the bender is set up to make the mandrel bends needed. The handle changes positions for a bend radius greater than 90 degrees which is a lifesaver. However, on that moveable handle the pin holding it in fell out on the 3rd bend. Not a huge issue, stake the hole a little bit and press it back in. It's cheap chinese made. The materials and design are sufficient enough to get the job done, just assembly quality issues. Compared to the same thing for upwards of $200, I can make this work. If I did this for a living I would opt for the higher quality tool.
Bluelight
March 15, 2025
I used this to bend up some stainless tubing for a hydroboost system on my olf mustang. This tube bender works as well as the fancy ones we have at my work. The only negative is the retaining hook is fixed, where the expensive ones fold over. I had to remove the hook on one complex tube to get it off. Overall, this is a great value tool.
Paul Bresee
March 4, 2025
This thing is off there's no way to make an accurate bend you'll end up wasting steel tubing Go with something that has a lifetime warranty
Gregory Illes
February 26, 2025
I took a chance on this, and won. It works very well and is really reasonably priced.The picture is of a 1/2" mild steel tube with a 1/16" wall -- the kind of general-purpose metal you can buy at Ace or Home Depot. It bent fairly easily, with some serious force but not at the hernia level, and no kinking or flattening or deforming. Exactly what I was looking for.This will be a great tool for making up welded-steel frames, brackets, luggage racks, etc.Happy camper.
Normand Aubin
February 9, 2025
Bent 3/8 Nickel copper fuel lines. Works well. Only down side is their size. This bender is big. Well fabricated.High quality item
Jackie
January 25, 2025
It is completely matched our need
Clinton Callbeck
December 24, 2024
Works good for the price
dan knowles
December 18, 2024
i really liked how easy it bent the tubing.
Customer
December 17, 2024
Its no where near the quality of ridgid
Recommended Products