Your cart is empty.
Your cart is empty.If you’re looking for a powerful way to keep your bike strapped to your trailer while transporting, you’ve come to the right place.
Pit Posse’s wheel chock is designed to hold your bike’s front wheel down to withstand any ride or travel.
✅Will keep the front wheel of any motorcycle up to 3 1/2 inches wide
✅Mounting points allow the chock to easily be removed when the truck bed or trailer is needed for other loads
✅Mounting hardware included
✅Made from 7/8" steel tubing and powder coated black
✅5 year manufactures warranty
✅Additional hardware kits available so a single chock can be used on multiple locations
ADD TO CART TODAY AND ENJOY A FULLY CUSTOMIZABLE WHEEL CHOCK
chris Davis
September 4, 2025
As others have stated, the bolts were not long enough and had to spent another 20 bucks to get longer ones. I took two large Harley’s 1800 miles round trip and no issues. Very sturdy. I had others that bend. Not these.
M. Ostlie
July 26, 2025
Came as advertised. However, you may find that you have to raise the front tire off the mounting floor to protect the disc brake. I found that I needed 1-1/2 inches rise to assure that the frond disc did not come into contact with the disc of the braking system. I'm using this system to haul two scooters (125cc and 200 cc) on a 5' x 8 ' trailer. I mounted a small 2x4 inside the wheel chock that the front wheel sits on top of. That allowed plenty of clearance even when the front end was compressed with the tie down straps. Chock and modifications work great for my needs.
Jason bland
July 2, 2025
Really like these. Easy install durable and easy to remove if need be
chris stewart
June 18, 2025
Nicely attaches when i need them and detaches when i dont. Holds every size bike i have from a 50 to a 450
NJ Zombie Guy
April 9, 2025
The Chocks themselves were perfect. I was worried that the pegs for the brackets would not line up like some of the negative reviews complained, but mine were perfectly straight.The hardware is robust, but the finish off the screw holes and peg receiver on the brakes is not perfect. I had to use my drill to clear the holes on a few of the brackets so they were rounded and accepted the screws properly. I did this easily by drilling the screw holes into the wood THRU the bracket itself.NOTE: don't use a drill/driver to put the nuts on the bolts/screws. Use a ratchet and socket. The one nut I tried to use a drill to make my job quicker cross threaded. Luckily the bolts are long and i cut it down and started over. Nylock nuts don't like speed.
Lester Wright
January 13, 2025
Fits motorcycle tires perfectly both my dirt bike and street bike
RC
December 31, 2024
I ordered two. They are slightly different. One was 3 1/2 inch spacing and one was 4 inch. Measure each one before you drill into your floor and test it. On one of mine, the peg was welded crooked. We had to put washers between the floor and the bracket for it to work. I would have sent it back but we needed it right away. The screws were too short to go through a 2x6. I had to buy 2 1/2 inch screws. Set me back $36. Also, as others have mentioned, each side is bent different. They are not perfectly lined up or straight. I can see where I'm probably going to need to sand them and paint them. The finish is thin in several areas. This might really bother some people. I guess you get what you pay for.
Beth Kollman
December 17, 2024
These do not fit a motocross bike front tire. They are the narrower ones 11-018 that say for mx bike. Maybe a bmx pedal bike but not a full size 250 or 450 mx bike. since i didnt get around to installing them for couple months it would be a hassle to return so i just bent them open so they did fit on tire. No big deal as they are just pipe. Well after bending them open to fit tire i lined them up drilled holes, test fitted. Everything was gonna work out alright then the next problem, i started to install the supplied locknuts on the supplied bolts. First two tightened fine then third only tightened half way. Thought maybe i cross threaded it so I continued to to the next. Also only tightened half way. Wtf. Well maybe i cross threaded that one too. So i be extra careful on next one and it tightens fine. Start installing another being very careful and only tightens half way. F This. I gring all of them off and am now going to hardware store to be bolts and nuts that work. I will never purchase a pitt bosse product again in my life. If they cant send a bolt and nut that thread together im scared as to what else they cut costs on. A 1/2 hour project took me two hours and still half to do it again if i decide not to just throw them in the metal scrap pile.
Recommended Products
