Your cart is empty.
Your cart is empty.Product Description
Propane Gas valves are made of high quality brass, safety and durability
- Inlet Thread:Female M10*1(0.394")
- Outlet Thread:7/16”-24UNF Thread(0.429" )
Thermocouple with high quality solid brass material
- Thermocouple wire:350mm
- Pilot Burner Connection Thread: M8*1
- The valve is for low pressure only
- Bakelite knob D shaft 8mm, using ABS material, solid structure, durable.
- FD4 weak current tilt dump switch gas R≤10 mΩ
- Wide range of applications
- Easy to install
- Good value for money
- Long service life
Work with outdoor propane patio heater, standing patio heater, room Space heater, tower glass tube heaters, table propane heater, Hampton bay patio heater and other Thermoelectric propane gas products. The valve is for low pressure only.
Edwin Winkelmann
2025-07-12 15:01:05
work great
trash man
2025-07-04 11:08:19
Perfect replacement for the old part. Did not see any difference.
Christopher cline
2025-06-10 20:10:47
Did not fit to my outside heater which the description said it matched.
Douglas
2025-06-05 11:37:11
This is replacing an old squeaky propane patio heater valve. Easy to install. Comes with all the cables and tilt switch.
Smokey
2025-05-16 11:57:20
Was sorta difficult to install. Works very smoothly now.
Daniel Ordaz
2025-05-03 14:33:48
While advertised to fit my Fire Sense patio heater, it did not. The replacement part had an extra port and I could not find a metric plug to plug up the opening.
john box
2025-03-26 14:44:37
was as good as original part
Steve111
2025-03-01 09:02:51
I ordered this 3 part kit because after trying all the suggested fixes I found on YouTube (for example; sanding/cleaning the thermocouple, bypassing the tip-over/dump switch etc.) I still had no clue as to why my Hampton Bay 48,000 BTU Patio Heater (purchased at Home Depot a little over a year ago) would not stay lit after releasing the gas valve control knob even waiting for about 2 minutes to do so (giving the thermocouple more than enough time to heat up).Bottom Line, the gas valve in this kit was useless to me since it did not match my heater, the dump switch looked to be the same as mine but I never had to try it, and the thermocouple didn't match either since mine had a threaded body for mounting it and this one did not (it was just smooth).In spite of that, my unit's problem turned out to be that the thermocouple had a broken wire right at the thermocouple (likely due to all the heat cycles, so not repairable) and I was able to remove it and then find a way to get the new thermocouple to stay in position (Note: The leads/wires were plenty long enough for my heater). After putting it all back together, it worked! So, not the ideal solution for me but it's now working again so I'm happy! :-)
Rick W.
2025-02-25 18:35:16
Good quality product worked very well just a little short
Customer
2025-02-21 14:27:23
I received the part exactly as pictured. What I failed to notice is that my part had a male fitting for the flare which connects to hose. I needed three fittings at Home Depot at a cost of $10.00 to make it work. Otherwise works great
Steve C
2024-12-21 10:01:05
Defective out of the box.Old gas valve stopped working so I purchased this replacement.Replaced the valve and lit the heater.Pilot was 2x too high at start.When I turned th gas knob toward Low the pilot lowered slightly and the burner would light of you were very careful not to turn too fast.Once lit the main burner flame woild not go higher.On High the pilot was almost out and the main flame was still not much higher than it was on low.Total waste of time.Received a refund as it is not returnable.Don’t waste your time.
Recommended Products