Your cart is empty.
Your cart is empty.Run your preferred tire size on your Chevy 1500 with Rough Country's Inner Fender Trim Panels! These handy panels offer a more elegant solution for running wider, aggressive tires and wheels without any unwanted rubbing from the front inner fender. In some cases, larger, aftermarket tires can rub under a hard turn or full suspension compression, causing undesirable wear and noise. Additionally, some of the wider wheel widths and offsets require a bit more clearance. This problem can be mitigated by trimming select portions of your inner fender, but in the end you're left with an obviously unfinished look, and often resorting to zip ties or other means to hide the fix! These durable, laser-cut panels allow you to perform the appropriate trimming, gaining up to ?? of crucial clearance where you need it most. Rough Country's Inner Fender Trim Panels reuse the factory GM corner guard, retaining the factory look for a fully functional inner fender that's more becoming of your lifted truck!
Customer
2025-08-10 20:00:54
Installed new wheels/tires (20x12 -44, 285/55r20) on 2015 Silverado High Country, could only turn half way to lock. Rubber very bad on both sides. After installing this product there is zero rub at full lock. Installation is pretty simple, does require metal trimming. I would recommend this product to anyone in a 14-18 Silverado/Sierra with tire fitment issues.
Customer
2025-07-27 15:28:26
Instructions were good and fit like a glove. Did exactly what it was supposed to do. Very easy task. Turning 33/12.50/22 on 12 wides -44 offset with no scrubbing after this nor cal mod and a 3 inch motofab leveling kit was installed on my truck.
Andrew
2025-06-18 17:16:34
Followed video instructions online rather than those that came with it. Plate works well, and does everything it’s intended to do. Currently have King 2.5s set to roughly 2.5" of lift. I am running 295/70r17 Cooper AT3 XLT on Method 17x8.5 0 offset wheels. Did this modification to run 315/70r17 Toyo Open Country AT3 tires. Only issues during install were dealing with GM engineering, trying to get the expansions nuts for the fender liner to stay in place, and removing those white plastic mounding clips for the fender insert.I would recommend getting extra mounding clips in case you break one, and to have small plastic pry tool. I happen to not break any, but I completely tore up the gasket/sealer that goes underneath it.I would also recommend getting extra fender liner expansion nuts, as I broke the tabs trying to bend them in a way to prevent them from pulling out of the plate. Note, you should not have this issue if you are not running mud flaps. Also, I used a 1†long M4.2-1.41 (#8) screws as opposed to the original fender liner screws as to gain more screw length due to the additional thickness caused by the mud flap.
Denise
2025-05-08 13:46:31
good product but lacks on instructions if your cutting make sure you know what you are doing
Dan
2025-03-16 13:02:47
This is a must have if you are doing the fender mod to fit bigger tires. After the metal cutting and trimming, these plates make everything bolt back up and look like nothing was even done. If your tires are rubbing at full lock doing this will definitely help. Also check the clearance on the front wheel well where you can just install some zip ties to pull the fender liner forward. Stop all the rubbing my truck did after installing 35s on a 7" lift. I think my wheel offset was a bit off because I didn't think they should rub but still did at full lock. These mod fixed the issue and looks professional. Get them!
Teufelhunden
2025-03-08 13:43:34
Fit like a charm. Instructions were good, just be ready for tight places for fingers and wrenches lol.Only thing I had to do was reverse one of the screw clips so it didn't pull out.
Justyn
2025-01-23 10:40:45
It worked perfect for my situation I have a leveled lift on my 2015 Silverado and wanted to fit 285/55r20 tires on 20x10 -25 offset wheel and it cleared perfect on the inner fender I did have to trim the front splitter but that doesn’t have to do with the product
A. Aven
2024-12-23 21:59:19
Works well, got 34.6†tires to fit with rubbing only at lock. Previously was not doable without the kit. Currently Bilstein 5100 at lowest level, plan on 2†level with 5100s at next to lowest
Recommended Products
