Your cart is empty.
Your cart is empty.Replacement Seats and Springs compatible with Faucet RP4993.
r2
2025-08-27 16:20:33
Tried a purchase from another vendor, those were junk. Tried these and the ones I received are what they should be, and work. Many other ones I have tried, even from the hardware stores, have the hole being larger, so the leak/drip. These ones have the smaller hole on the rubber seat. They are not soft like some others, but firm rubber. So far, I have not had any leaks or dripping (as I would after a few days with the others). Glad to get something that actually works like it should. These will work with Delta/Glacier Bay bathroom faucet.
B. Clark
2025-08-04 12:35:56
I bought another brand, advertised as compatible. They started failing & the faucets were dripping again! My search for better seals & springs found these.The Pros:+ Pretty good customer product reviews.+ $9.87 with free Amazon shipping when I bought these.+ Sold as a 4PK = 8 Rubber Seats and 8 Stainless Springs!+ These look exactly like the Delta factory/OEM parts, down to the ground flat stainless steel springs!The cons:- None so far!Closing remarks:â–ª I normally never give a 5 stars right away, but I'm impressed with these low cost, quality replacement parts!â–ª When we installed these, we applied a small amount of Haynes Lubri-Film onto the cartridge seal sliding surface as well as on the cartridge O-ring seal.
Donald D. Kikta
2025-08-01 21:36:09
Fit correctly, no muss
elizabeth
2025-05-24 14:26:55
These went in to replace original Delta bathroom hot water faucets that were leaking. They are tiny so you need something long and thin to put them in place and to remove the old ones. Work fine.
M. J. Foley
2025-05-13 18:41:03
If you are a do it yourself plumber these are a must. I keep a couple in my toolbox just for when that sudden leak shows up.
PattyD
2025-05-08 18:29:07
It was easy to replace but you need to be careful how you remove the old ones. Follow the instructions carefully. I also used a light coat of plumbing grease. Don’t over tighten it, this is one reason for drips or leaks. They fit and work great. No leaks.
Bob Mally
2025-04-29 12:23:07
I found the manual for a 27 year old bathroom faucet that was leaking badly. I was able to order the original replacement parts via the part numbers in the manual. They arrived quickly. I was able to fix the problem completely. Great transaction and seller.
TH
2025-03-16 15:30:56
This is what I experienced with these replacements. The holes are smaller than the oem rp4983. It definitely impacted my water pressure quite a bit. Went to Home Depot and got the Delta brand and my pressure went back to normal. Maybe if you have really good pressure to begin with it won’t make a difference but I say stay away from the replacement brands.
PETER WALL
2025-03-06 17:25:25
Fue lo que pedà instalación fácil
Serg
2025-03-04 13:01:41
Stopped the drip. The cost is 1/4 of the brand name Delta parts.
Sherif Assran
2024-12-24 11:12:20
I used the product for Delta shower jet faucet
Alan
2024-12-07 13:02:47
Masco Canada/Delta did NOT provide a lifetime warranty for my Delta 1300/1400 series shower faucet. I will never buy any delta products ever again. They are suppose to provide replacement valves according to the contractual agreement.On the phone the Masco "consumer specialist" suggested a sure fire repair to the 19804 valve was to fix it with these seals.Replacing such seals is childs play. Even cleaned the inner faucet section and turned the water main to flush out any debris while the 19804 valve was not installed.After the new seals installation the faucet leaked similar to the old worn out valve. Ended up buying an OE original 19804 valve and it resolved the dripping faucet.DO NOT be frugal. Just go out and buy an OE original valve. Waste of time and effort using 3rd party seals or aftermarket replacement valves.Even though it takes approximately 10 minutes to turn the water main valve, loosen 1/8 set screw for handle, removal of collar. R&R of seals, re-installing valve with "Hot" designation of valve on left hand side. Waste of time as i must do the job twice.Do it right the first time.....or don't do it at all!!
Recommended Products
