Your cart is empty.
Your cart is empty.Product Description
SAMSFX Fishing Fish Cleaning Board Clamp is made up of stainless steel material, durable and solid for use. Great for hardwood fillet board, make fish cleaning, bait cutting for boating camping or home. The clamp holds down the fish by the tail for easy filleting, secures fish to a table, board or bench. Mounting hardware included 6 pieces Self-Tapping screws, easy to setup to the board. The spring on the clip is very sufficient for the job of pressure.
BOLD & HIGH STRENGTH SPRING
The spring is very tight so it clamps down tightly.
The clamping force makes the clip firmly hold the fish for securely for cleaning and filleting.
We tested and cleaned 4-20lb Salmon and no issue holding them.
It works great on bait mullet, salmon, steelhead or smaller fish as well.
6 PIECES SCREW HOLES
Attached to the cutting board via 6 stainless steel screws, it provided screws result in a solid mount.
It havs a one hole in each corner but also a sliding one in the center of each side.
This allows you to screw the screw into the middle hole first, and then adjust the clamp so that it is positioned in the way you want.
TIGHT & SHARP TEETH
Fish Cleaner Clip can clamp the fish tail firmly, the fish will not jump.
It really helps to keep the fish's head in place while you worked the fillet knife.
It has a strong bite although sometimes fish tails aren’t strong enough so need to clamp on some actual meat.
Sharp sawtooth mouth grips fish pretty solid and doesn't let it go.
GREAT FOR SPINY AND BONY FISH
The cutting board is not included.
It can be mounted anywhere you need to fillet fish, when fly fishing, kayaking, camping or home kitchen.
You can also mount the clip on the hardwood fillet table or on the side of the boat.
A must clamp for safety and ease when skinning fish.
Shelly
2025-08-23 12:48:02
The product works great, I installed it on my boat to filet fish. Great value for the money. Grips the fish nicely.
Customer
2025-08-14 17:01:25
Replaced an older version of clamp Worked great. All I have to do now is catch fish to try it out.
Wylie Wiggins
2025-07-19 16:27:33
I've used these in the past, they're alright for the usual eaters, serious toads, your mileage may vary.
D. Webber
2025-07-11 16:44:22
Strong clamp. Made well.
J Engineer
2025-06-10 14:03:43
Teeth are sharp and the spring is strong. Perfect size for fish like bluegill. Also used it with a 12" -ish bass. Haven't cought anything bigger or mounted it yet.Currently I'm just setting the handle of a cutting board through the space behind the teeth. Wobbles around some but still helps hold the fish. Didn't notice that the cutting board was only 1/4" thick when I ordered it, otherwise would have used the screws. Might try a different board or cutting the screws shorter. If I can get it to work, it will be less expensive than buying a pre assembled fillet board.Have only used twice so far, so will update if I have any issues later on.
AntBme
2025-05-14 10:48:19
Board left over from a home improvement project was perfect for the clamp. Works great as a filet board fish clamp.
Tony and Melissa ATL
2025-05-06 15:02:45
We've been making custom filet boards for friends. These are good quality and make a nice addition. We used deeper screws and the included ones work fine.
TCIP
2025-03-30 10:25:45
I attached this clamp to a piece of composite board and it works very well to hold my fish for scaling.
Coldo
2025-03-28 20:03:50
It clamps fish in a decent way, easy to clean, should last a while
Ryan
2025-03-18 14:07:07
Works great for small to medium size fish. Haven’t tried it with a huge catfish yet but I think it will hold.
Clive B.
2025-03-05 17:31:15
Was concerned about the strength of the "clamping force" after reading some reviews. I ordered two. Put them side by side on my bait table. One would have been quite enough... I clean 4-20lb Salmon and no issue holding them...
Nick
2025-02-12 12:16:33
Good helper after fishing )
Recommended Products