Your cart is empty.
Your cart is empty.ThIS Santa Barbara Surfing 9in fin is a perfect fit for Longboards and Standup Paddleboards either with or without side fins. Fits any US standard fin box and comes with both the brass slider pin and the fin screw and plate. Great for surfing, noseriding, and flat water touring. Ready to put on your board and get in the water. Direct fit for all standard fin boxes of longboards and surfboards with single or tri 2+1 fin setups. And for sups that includes all paddleboards including BIC Stand Up Paddleboards and other popular Paddle Boards found at REI and other outlets. There are some inflatable paddleboards this will not fit on, refer to the photos. This sup fin will get you on the water and stoked out of your mind. This Sup fin is a great paddleboard accessory and would be a great paddleboard gift. Purchase our sup fin and get a free sticker as well as all the free hardware: fin screw and plate, and brass slider pin.
AF
2025-08-30 12:43:07
These fins are awesome! They fit easily into our 10ft fiberglass stand up paddle boards. They are easy to put on and take off and help stabilize our boards. I highly recommend as they are made well and are a great value for the cost. We have used them once but I’ll update if anything changes.
Photoleif
2025-07-27 16:54:26
Review only from the perspective a nonstandard use. I'm sure it is great for its intended application as well.I needed a replacement fin for a Perception Hi Life 11ft hybrid that was outright missing its fin. This size of SBS fin is an exact fit in terms of the hole for the thumbscrew, the 'foot' part of the base, base width and length, and general fitment in the fin box. What does not match, if you're wanting to use it for a Hi Life, is the supplied thumbscrew. What comes with this fin is a M4x0.7 screw and nut, and a high-quality set at that. What the Hi Life's body-mount nut needs however is a 10-32. Additionally, the Hi Life's fin box is slightly too short for where the supplied nut requires it to be situated in the fin box. This slight misfit is due to the inside angle of the box housing, which obstructs the new nut from fitting directly below the thumbscrew hole. Thus to make the SBS fin work with the supplied nut and screw, you're either boring a new hole a little bit back from where the Hi Life built-in nut is situated, or you're supplying your own 10-32 thumbscrew and using the Hi Life's body-mount nut. Either way would work and let you enjoy this nice fin.Again, this is an admittedly nonstandard use for a great fin, and I'm very happy to have found this product. I used a 10-32x0.75" screw with a small stainless washer topped with a small rubber washer to hold the metal washer onto the screw. This worked great for a couple hours of testing on a choppy lake, and on another outing for a 5-mile adventure in mixed conditions. The screw I chose to use keeps this from being a tool-less solution, but it beats the heck out of the alternatives if obtaining a replacement Hi Life fin is slow.To summarize in case anyone else is wanting to find a Perception Hi Life 11ft hybrid kayak replacement fin: this fin itself fits perfectly in the Hi Life, and in fact it could be the same one that comes with the Hi Life. What's different is the thumbscrew; to secure the fin with no drilling, you will need to supply either a new 10-32 screw (appx thread length 3/4") or use the thumbscrew that presumably came with your Hi Life. In the latter case, this fin is an exact fit. In the former, it's up to you to locate a thumbscrew you like, and a washer. The washer is appropriate to keep the thumbscrew (or screw head) from damaging the plastic shoulder of the Hi Life fin box.
Upton
2025-07-15 10:43:26
Replaced a lost perception hilife11 fin. Go to local hardware story for a 10/23 1inch screw (ideally with wing nut on top) for the screw if you need a replacement for that. Worked great.
Kathleen C Riley
2025-07-08 10:00:25
I have a Bic Performer 10'6" board, and this fin is a direct match for a replacement fin part. Easy to install on my board, firm grip in the track using the provided screw, solid construction, really polite customer service email immediately after the sale, super cooled company website with lots of information, and I'm so glad to have found this replacement part. Looking forward to getting back out on the water post-lockdown to test it out but it seems like it will be Surfs Up then!
JeannieD
2025-07-01 17:57:06
Pretty bummed to have to send this back. Do not consider "specifications" the measurements to determine the fit.
Kailua Sam
2025-05-30 13:29:36
Hunted high and low for a center fin for a used C4 Waterman, 10' 6" SUP that I bought without fins.Couldn't find anything that told me it would fit and the C4 site sucked royally without any info either.This fin fit well though I did have to file down the two brass pegs at the back of the fin base in order to fit the track inside the fin box. After that, it fit perfectly.The fin looks good and I'm confident it will do the job well.The fin came quickly...I'm a happy camper
Hangtown Outdoors
2025-05-12 10:56:53
Perfect for used paddle board I picked up that didn’t have fin. Works great on 11 foot hard board.Recommend.
Corrie L.
2025-02-20 20:42:13
This fin was a good replacement for my lost Atoll iSUP fin at a fraction of the price. I’ve used it for most of the summer now, and it’s held up. It has the same issue of being held in place with a screw as the original, but as long as you don’t skip that step, it’s easy to install.
Recommended Products
![Ho Stevie! Quad (4) Surfboard Fins - High Performance HexCore - Built for Speed and Drive - [Choose Base] with Fin Key, Screws, Wax Comb and Travel Case](images/loading.gif)