Your cart is empty.
Your cart is empty.
Set of 4 Engine Motor and Trans Mount Compatible with 2006-2010 Civic 1.8L Automatic Transmission
Compatible with
2006-2011 Civic 1.8 L
Replace OE Number:
A4530, A4534, A4543, A4546,
EM9280, EM9218, EM9213, EM9216,
9280, 9218, 9213, 9216,
50890-SNA-A81 50880-SNA-A81, 50850-SNA-A81 50820-SNA-023
Package Includes:
A4530 Front Right Motor Mount,
A4534 Torque Strut Front Lower Mount,
A4543 Toque Strut Front Upper Mount,
A4546 Auto-Transmission Mount
Drake the snake
2025-09-06 11:13:21
Installed all of them and worked perfectly. Seem to be well made and not too cheesy. Both of the mounts on the top side of my engine were completely broken on the rubber part. The one underneath the engine still seemed decent but I changed it anyway. This is such a great deal and if they last 100,000 miles I will be happy with that
x
2025-08-30 15:46:41
Fits well against oem.
Pedro
2025-08-05 16:58:37
Not the best, had some trouble with the original bolts, they didn’t fit well, but they got the job done!
ANTW731
2025-07-04 17:53:42
I received the engine mounts in a few days ... quality parts for the price. Easy installation
Customer
2025-06-24 14:18:14
This was a great DIY and only took around 90 minutes to replace all 4. I did do research on you tube for remove/reinstall. If you do it yourself buy ratchet wobble extensions. I didn’t have to remove parts to get to the bolts. It saved me a lot of time. My car is quiet and shifts are so smooth. I feel like I’m going slow now even though my speed is 70+ on the freeway. Best upgrade for a 2010 Honda civic coupehttps://a.co/d/07IT38Xl
Derek
2025-06-05 20:43:36
The main engin mount was hitting the frame and I couldn't line up one of the bolts. Once together, the braket going from the top of the engine mount to inside fender was off by about half of an inch. I needed ti expand the slowed holes to get it to line up correctly. When bolting everything down I noticed one piece wasn't sitting flush because the hole wasn't tapped deep enough when using the stick hardware and was bottoming out the threads. What should have been a 2 hour job, took me about 10 because I keept putting it together then taking it back out to figure out what was wrong. The few bucks you save on these mounts gets lost in the labor it takes to make them work.
Koi Kurama
2025-05-20 16:29:53
Got my items quick and was easy to install by the mechanic. If you looking for a good non expensive alternative id get.
Valeria & Isaac Marroquin
2025-05-06 18:31:32
They looked promising at first. All parts showed up. Driver side trans mount was the easiest one to install, with no problem or adjustments done. I installed the passenger side engine mount, that one gave me trouble. Other reviews on here seem to run into a few problems with that side mount. What I ran into was, it’s a two part mount, the bottom portion was fine, the top t bone pulley part (looks similar to engine bottoms mount), it was 1/4†to long from center of top bolt to the two bottom ones. OEM is ruffle like 7-1/4â€, this one was around 7-1/2â€. Bottom mount was ok. A bit off but it went in.Driver side mount took me like 30-40 min to change.Passenger side mount - 4hr 😠only bc bolts on engine are tight, I’m guessing bc of heat and a lot of vibration.Bottom mount - 30 min
Miguel
2025-01-08 17:38:43
La verdad los recomiendo funcionan perfectos me.llegaron en buen estado ,y al instalarlos funcionan muy bien callan el sonido totalmente llevo 3 semanas y conozco a alguien que los instalo estos mismos y lleva 9 meses con ellos por eso los compré .
Recommended Products
