Your cart is empty.
Your cart is empty.Product Description
Proudly Made in the USA!
Weight: 85 Grain, 100 Grain, 125 Grain, and 150 Grain
Sizes:
- 17/64" points typically fit weaker spined small (.204 ID) shafts
- 9/32" points typically fit stiffer spined small (.204 ID) shafts
- 19/64" points typically fit standard carbon (.246 ID) shafts used for hunting
- 5/16" points typically fit stiffer spined standard carbon (.246 ID) shafts
- 21/64" points typically fit large aluminum 21 series with inserts
- 11/32" points typically fit crossbow bolts
These Combo Points are endorsed by 3-D and foam target manufacturers
Made in the USA.
- Made of tough, rust-resistant steel with a black zinc finish
- Computer generated, aerodynamic design cuts wind resistance and increases arrow speed beyond 2 yards
- Combo points have a longer length and innovative design
- Low Drag & Matt Wear
Treads2
2025-08-21 12:36:46
These are worth the money they are charging. If I had a problem, it would be that I haven't found this contour (shape) in any finish other than Black anodize. I was reading ALOT of the Q&A's on this Board and have to put in my 11/32" cents. In my experience in Crossbow target shooting (easily 10,000's of shots), the OD or Outside Diameter of the Bolt and Field Point should be as ABSOLUTELY close together as possible. In a Target,( Morrel, Spyder packed foam or others) any difference in OD causes DRAG either penetrating or removing from a Target for 400 fps or faster. Check it out with any Bolt that you can do without. Pulling out the intersection of Point and Insert is tearing target material out. I have tried: rotating the Bolt prior to removal, pushing the Bolt farther in and pulling straight out, etc. I now have a few Targets with several thousand grains of added weight since I bought them. 1 more thing, if the Bolt diameter is Larger than the Point, I am sure somehow it will be a concern when calculating the induced drag and loss of airapeed.
Dan
2025-06-02 15:41:48
I really like these except the threading. About half of them were extremely hard to put it. I checked the thread size, which was correct, but it didn't feel like they had been deburred.
Lorna N.
2025-05-06 15:37:55
Perfect for 5mm arrows! I was looking for 150 grain field points for my 5mm arrow Victory RIP, would also be perfect for Easton axis or FMJ. Threaded in just fine and was perfectly flush with arrow shaft.Don’t trust the description, it’s not grams it’s GRAINS
ROBERT H.
2025-03-24 12:13:04
What more can i say here. Made in the USA is one great reason to buy these. I never put them on a scale but the 17/64 was nearly a perfect fit for my Carbon Express Reds. 400 spline. They was flush with the shaft. However i have some Easton arrows that was 400 spline also but they had the inserts built into the arrows and for some reason they wouldn't fit down inside of those shafts. Like where it tapers from above the threads. That wouldn't fit inside those arrows. But they was a perfect fir for my carbon express ones. The easton arrows was very old also. Like 2005 models. Great job. I haven't weighed them but i trust it. Made in the USA i recommend strongly!
Dan Clark
2025-03-17 10:23:52
The target points were exactly what I needed. I was trying to find a very small diameter (17/64) and a very heavy point (150 Grain) and I was having no luck until I found this. My one concern when I ordered was that the weight was listed as Grams instead of Grains but I assumed that the seller was ignorant to the difference between grams and grains and I took the chance. Turns out that I was right. They were indeed 150 GRAINS and I have exactly what I needed to screw into my new Carbon Express Pile Driver PTX arrows. Very well machined points too and the weight tolerance is very close.
Technical Expert
2025-03-13 16:01:19
I looked all over my local area for a heavier 150 grain field point to no avail. I recently acquired some 150 grain broad heads and no practice points. Thankfully Amazon had these and I was in business.I really like these field points as a heavy point option. They shoot accurate, fit into the arrows well, extract from the target with ease and are durable. I would definitely recommend these to friends looking for a 150 grain point. They are definitely worth purchasing again and are value priced.
Owen
2025-03-02 16:42:37
All tips weigh in very close to each other. Hooks up well to most targets. A few are starting to bend a tad at the tip after a few hundred shots
Garzas Outdoors
2025-01-11 14:39:53
Algunas vienen sin rosca
Recommended Products