Your cart is empty.
Your cart is empty.Product Description
AF Phil
2025-08-05 11:25:22
These are working well, but I have one note to pass along. I was hoping to use the quick release mounts to be able to remove the casters when they weren't needed. However I'm mounting these on wooden table legs and the wood screws will not fit inside the quick release brackets and allow the caster assembly to slide in. The wood screws are round head and don't allow the caster assembly inside the bracket. The flat head screws that would work with the quick release brackets are machine threaded and are secured using a nut and washer on the other side of the leg. The legs on my table are too large for the machine screws, therefore I was stuck mounting the casters directly to the table legs using the wood screws.Aside from this one disappointment, the casters work great and allowed me to move my table without effort.
K. ONeill
2025-08-03 10:21:17
Exactly what I wanted. I put them on a workbench I may want to move once a year. I don't want it on wheels all the time, I just want to be able to move it easily every once in a while.So the plates are easy to install. Use a 2x4 as a spacer. Set the 2x4 on its side, set the plate on top, screw into the wood. Very fast and easy and all the plates are at exactly the same height.I was putting it on a bench with 4x4 wood legs, so I tossed the included screws and used 3" deck screws. Worked great.The images have a very good idea. I bought some small round magnets, drilled out little pockets for them on the inside of the bench legs, and glued the magnets in. Now I have magnetic holders for the wheels and L-pins so I don't lose them.10/10, just great. Much better than having the bench on wheels all the time. I've only had them a week but the quality seems fine. Roll very easily. I'll update if there are any issues.
Mocha Tan
2025-07-17 17:29:37
Well made. Simple mechanism. My workbench now sits solidly on the ground when in use but is easy to roll away when I am done. I have tried other caster systems with wheel locks but the bench remains too “wiggly†when in use.I mounted the brackets to the inside of the 2x4 legs so they are not a tripping hazard. Love the ease of bracket install and subsequent caster installation.Downsides:1. No way to micro adjust leg height if floor not level. This can be solved with addition of leveling feet to the bottom of the legs.2. Instructions are minimal. Calls for “1.4 inch†spacing from floor (why not 1 3/8 inches?). Comes with pan head screws for use without the brackets or thru and thru bolts for use with the brackets. They are NOT interchangeable but this is not spelled out in the instructions.Overall a very clever system that provides a safer, more solid workbench. Would have given it a “5†if not for the weak instructions.
Dale Goynes and Laura Goynes
2025-06-18 12:51:58
Installed four of these on a mobile assembly table/cabinet in my shop. The table weighs about 500 lbs with tools and these casters handle it well. Being detachable is very convenient since it says me tripping over them when I am using the table.
I. T. Chew
2025-05-26 09:13:25
I used the option to have the wheel unit detachable from the base plate. I chose to use my own stainless steel screws to mount the base plate. I attached these wheels to an outdoor Gazebo so that I could move it around a deck. Found it easier to leverage each corner and then locking down the wheel (insead of using the stepping lever on the wheel). Once each wheel is down, rolling the Gazebo was easy. Afterward repositioning the Gazebo, lowered it and removed the wheels for storage (do not think wheels are rust proof).
cz85b
2025-05-21 13:15:01
UPDATE: so when I pick up one side to move my desk through the sliding glass door, the wheels just fall under the feet of the desk. My plan is to fabricate 4 pieces of metal to bolt through the same holes as the bolt that holds everything together. The goal is to create a stop so that the wheel does not fall under the foot of my desk. I will update with a photo when I complete this part of the project. (My goal with all of this is to give the manufacturer ideas on product improvement, because I genuinely like the idea, I just want something better.While these were reasonably priced, Installation is not always easy. I bought angle steel at the local home depot, and some 1/4" bolts and nuts. I put 3 bolts in all but the one in the front of this shot (oversight to be corrected) Everything has a drop of red Loctite on it so I don't have to revisit any of this. If not screwing these into wood, use the machine screws that come with that have the counter sink head on them. 2 of these hold the bracket with the pin that makes for easy removal. The 1/4" bolts with the countersunk screw head stuck out too far and made it impossible to slide the wheels in. while this might not be a terrible solution for some, I DO want to take them off at some point.Regarding the wheels themselves. Everything kind of flops around, and while a better design would involve some type of spring system where the wheels don't flop under everything when picking up the desk and putting it down, that will require a design upgrade..Positives. The angle steel I bought is really heavy. I don't believe it is going anywhere. The bottom counter sunk screw for the bracket is bolted onto the leg, the second on the angle. everything is really tight, and I am excited to use the new wheels, roll the desk out onto my deck, and work OUTSIDE when I work from home! I shared a picture (before I cut off the long screw and paint the angle semi-matte black) so you can sort of see what I did.One screw that is not visible went into the bottom part of the leg. The bracket hangs below that leg but not quite touching the floor when the wheels are up or off.
Charles Bratcher
2025-05-19 10:31:26
I bought these for an outfield table I am building for my tablesaw. Did not want a tripping hazard as I also use this for my assembly table. These work great
Cliente
2025-04-27 09:35:55
É um produto muito bom para suspender peças pesadas.
Chantal R
2025-04-24 16:13:22
Bought to put under Butcher's block and it works perfectly. Very sturdy!
Sarah Dickie
2025-03-11 12:08:05
Delivery early well packaged top items
Alejandro Hernandez Enriquez
2025-03-03 11:37:07
Las ruedas están bien, pero llego incompleto el paquete como se ve en la foto, faltaba una placa de fijaciónDevolvà el producto pero................... los precios se triplicaron al querer volverlo a comprarPaso de 790 pesos a 2,100 pesosAl parecer es un gancho para llevar primero a la compra para después vender más caro el producto
Happy cutter
2024-12-16 17:18:11
Fit for purpose
Recommended Products
$15.98
$ 7 .99 $7.99