Your cart is empty.
Your cart is empty.From the Manufacturer
Each jaw moves independently. Such 4-Jaw Chucks are used for holding odd shaped pieces or where zero tolerance is required. This 8-Inch 4-jaw chuck with a 1-15/16-Inch bore has semi-steel bodies and hardened reversible jaw.
Elliot H.
August 17, 2025
Appears well made and balanced . I need one that would front mount to put on a rotary table with "t' slots. This fit perfectly I also made a 50mm center to make it easier to center in a mill. One heck of a good price.
J&J
July 13, 2025
Not the highest of quality, I had to take the chuck apart and give it a good clean-out. metal particles, some rust and just general machining goo. The body has a run-out of about 4 tho, for general work holding or wood working its a good chuck, but for precision lathe work I would keep looking.
D. Wu
July 6, 2025
Big heavy Chuck, almost 40 pounds. Good fit and finish, few minor burrs. Believe this is a sanyu k72-200 chuck given the front label.
Dan Johnson
June 14, 2025
I should have bought a four jaw chuck sooner and this one was affordable and I was able to find a plate to adapt it to my lathe. I wish they had a drive plate for this chuck. I bought one and made it work. The other thing is this chuck is a little heavy for my Craftsman 12x36 metal lathe but it works and was definitely the right price. It more than paid for itself on the first project.
TigNewton
June 3, 2025
One of two brands of chucks distributed by "Woodstock International", "Shop Fox" being the other.In comparing the two brands, I'd have to say the Steelex is the lesser of the two. The fit and finish of the Shop Fox 3-jaw 6" chuck I have is superior. The Steelex is still quite usable and was well within the published specifications.A good fit for home shop use at an affordable price. And unlike the Shop Fox chucks for sale on Amazon, the picture of the Steelex chuck is exactly what I received.The chuck was marked with the "H" logo and is identified as a model "K72-200" dated 12/2005.Specifications:Radial runout, chuck OD - .06mmFacial runout, chuck face - .03mmFacial runout, upper jaw faces - .04mm50mm boreRegistration 125mm Dia.4 hole mounting bolt pattern, 104.8mm Dia.Mounting bolts are m12-1.5x80mm
Angela Gardner
May 11, 2025
Good price
Frank Cain
May 10, 2025
Looks great. I'm sure it will work as expected. Machine quality appears to be very good. will test after building a mount for it. Thanks
Eric
March 17, 2025
Much better than other reviews made out!!! Jaws are tight seemed pretty clean didn't have to clean out like others.I was concerned about ordering but, very glad I did!
Guy
March 16, 2025
tout es parfait
Gwen
December 27, 2024
Not as precise as it could be but adequate.
Argo man
December 12, 2024
I am a retired machinist and I think---for the money--this is a very good product.You can buy a BUCK for 5 times the price if you want to but for piddling around at home on a tiny 12 inch lathe it's great!
Will
December 10, 2024
Purchased this chuck some time ago and never got around to setting it up on my machine.When indicating the first piece put into the chuck, I was getting unpredictable readings / adjustments. I found that I could grab the end of the workpiece, and rock the workpiece back and forth.The jaws are so far out of square / bell mouthed with the center line of the machine, that they only grab maybe 1/8 of the material.Wasn’t expecting anything great, but I did expect something that would atleast hold the workpiece.
marcel g.
November 20, 2024
hard to set
Recommended Products
$82.60
$ 39 .99 $39.99
$199.99
$ 88 .99 $88.99