Your cart is empty.
Your cart is empty.TEMO 1/32 Inch Diameter Carbide Downcut Inlay Router Bit CNC End Mill 1/8 Inch Shank, Ideal for Wood Carving, Slot Mortise, Engraving, Grinding
yawnny
2025-08-16 10:53:51
i needed to do some minor inlay work on a vintage guitar, to replace a headstock logo.The bit I used, worked flawlessly, and the repair came off better than I had expected, dueto my inexperience with inlay work.Seeing how expensive these type of bits can get, I feel these worked just fine, and will hopefullyuse them more in the future.
PBrady
2025-07-27 18:31:11
I use this size bit for my dremel to help me with detail inlay work on guitars. cuts well, good price also
Gerald Freese
2025-07-20 11:58:03
Can't beat them for the price and work like they're supposed to...
Uknowdakine
2025-07-19 14:55:36
Used this bit as a detail bit for a 5 hour carve on my cnc router. I slow every motion down to ensure they bit wasn't stressed. 4.5 hours into the carve it snapped
BB
2025-06-09 17:10:03
These router bits are absolutely unsuitable for their intended purpose. I purchased two bits. Both broke the instant the touched wood. The pictures tell the story. How could a company think they could sell these bits and people wouldn't notice they are a scam? I just wanted to save others from wasting their time.
M. Redmond
2025-04-29 10:42:48
I used the 1/16" downcut bits to cut mahogany and maple. The attached pictures show the mahogany, all of which was cut with the 1/16" bit. The maple was largely cut with a 1/8" bit from a different maker, but the small holes in its center were cut with this 1/16" bit.I couldn't be happier with the results. No tearout or chipping at all. I ran the bit at 18,000 RPM and 36 IPM.
Customer
2025-04-24 16:48:27
They are solid, they are long.That being said , it can be good thing or bad thing . They are down cut router bits , I used the 3/32nd , and the 1/8th inch bits fine. But The 1/16th and 3/64th snapped immediately while I was trying to cut pockets for pearl inlay on a guitar headstock. The bigger down cut bits, work very well cutting bridge slots, but you have to make small cuts ( they are down cut) . But they leave a smooth bottom finish for the bone saddle to rest.
Scott Oliver
2025-03-11 15:15:02
Used it for some 5mm depth detail work around small lettering in tigerwood. I bought this bit simply to experiment with and based on how thin it is I was expecting to break it immediately. I was very conservative on speeds and feeds on my Shapeoko CNC, and successfully completed my first job. A useful bit added to my collection!
Kindle Customer
2025-03-09 14:25:01
I’ll be using these to do inlays in guitar fretboards. Did a quick test and they cut as expected.
Spectel
2025-03-01 21:48:42
To date I used the 3/64†bit in my Dremel rotary tool for inlaying copper wire into wooden boxes and the downcut flutes left a relatively clean cut. I will have to determine where to use the other sizes. I wish I had the option to substitute the other sizes in the package price. I would have ordered more of the 3/64 size knowing it’s the one I will use the most in the near future.
Jalp
2024-12-31 09:01:14
I’ve been using this bit for a while now! Engraved on walnut, pine, cut through mdf a few times. It’s lasting really well and I’ll buy it again when it wears out or breaks.
ron biersteker
2024-12-06 15:11:42
Worked as it should. Nice clean cuts in Black Walnut. Used in Shaper Origin handheld CNC router.
Ryan
2024-11-14 10:32:30
Product came pre broken. I'm hesitant to even use them if they broke on the way here.
Recommended Products
