Your cart is empty.
Your cart is empty.The POWERTEC 4-Inch to 2-1/2-Inch Cone Reducer allows you to connect 4-Inch port to a 2-1/2-Inch hose or a 2-1/2-Inch port to a 4-Inch hose. The 2-1/2-Inch opening also allows you to fit Shop-Vac, Sears and a variety of other wet/dry vacuum cleaners. Simple to install, use and uninstall for the utmost in ease, performance and reliability.
RoxyMT71
September 3, 2025
Fit perfect and work great on my fume extractor.
Kindle Customer
September 1, 2025
Perfect connection! Thick and the perfect size.
DR
July 26, 2025
This was an interesting buy. I was told the fitting was unavailable, but could be computer printed. It turns out that I didn't need it, but it was too interesting to pass up, and inexpensive. So, I accepted. It appears to be accurate, sturdy and perfectly acceptable for the task. The surface texture is a little bit bumpy, compared to a smooth PVC fitting, but well within acceptable limits. I am going to keep this around for show & tell.
Jeff Nalley
July 19, 2025
I bought a new Laguna 14 Twelve Bandsaw and needed to be able to connect my Rigid Shop Vac for dust collection. I purchased this PowerTec reducer because I knew it would connect perfectly to my shop vac. And I knew ahead of time that it would be the same diameter as my 4†dust port on my Laguna, so I knew it wasn’t going to simply slide over my dust port. But I had seen videos where other folks had cut a small section of 4 inch PVC pipe (Schedule 40) to use as a coupling. I did the same and it worked perfectly. I will say though that I had to lightly sand the inside of the 4†PVC pipe to reduce the wall thickness by just a hair so that it would slide on. It was not difficult at all. I didn’t have a Spindle Sander at the time so I glued a 2 inch strip of 150 grit sandpaper to a 1/2 “ dowel and installed it in my drill press. After running it around the inside of the PVC several times with the drill press set on medium speed, it was just enough to allow the PVC to slide over the dust port. You may not have this problem. The Laguna has an exceptionally thick powder coating finish on it which is very durable but probably also makes the outside diameter of the dust port just a hair thicker than some other brands, which explains why the 4 inch PVC needed just a tiny bit of sanding of the inside to make it fit.You can get a smaller length of 4 inch PVC at both bog box stores if you don't already have some or don't have a need to buy a full 10 foot stick of pipe.I absolutely LOVE the Laguna Dust Collection. Almost zero sawdust gets inside the cabinet or falls out onto the base. I still can't believe it. I've cut a few hundred feet of board and there is less than a teaspoon of sawdust inside the lower cabinet, and about a pinch of dust inside the upper cabinet. 99.99% of all dust gets captured through the dust port. Why other Bandsaw manufacturers have not copied their design, I will never know. Even bandsaw brands that use a tow-port design still have horrible dust collection. It makes no sense.Anyway, if you’re looking for a dust port reducer, this is the one. It’s very solid and thick enough that I would consider it to be heavy duty. Delivery was pretty good. No complaints.
Sergio Quintero
July 9, 2025
Complemento adecuado paracel sitema de aspiracion del taller
ken
July 7, 2025
Add hot air from my basement fireplace to my great room. Help with the heating bill . Just added fan.
Joel A. Mussman
July 1, 2025
It does what I expect, allows me to vacuum out the dryer duct.
Chad Anderson
June 14, 2025
This dust hood from POWERTEC connects easily with a coupler and reducer to your existing dust extractor setup. I purchased two of these, one for my miter saw and one for my table saw. They work great, but this thing really needs more of a flange around the outside to anchor it. If you're not right on the money with your cut, you're going to be repairing at the same time you're installing which is no fun. It worked for what I needed it for, but it wasn't the prettiest install.
shane
May 21, 2025
Very happy really good size well made
Customer
April 15, 2025
works as expected
Mick
April 13, 2025
Is not 4†when measured it’s only 3.9â€
C F Underwood
February 25, 2025
Great for use on my DeWalt thicknesser.
Dave Kimball
February 11, 2025
I got this earlier than expected an it works great. It's well made and durable and fits perfectly. However I should ass make sure you read ALL of the description as I have seen some negative reviews for Bellends who gave negative reviews about not fitting and explaining in detail how they tried everything to make it work EXCEPT follow the directions. you need to by the rubber flex cuff to attach to your machines. As this is a solie plastic and so is the out port on your equipment I don't know how people can't understand that there would be no way to put a hose clamp (or duct tape on this) and tighten it. So I would say disregard any reviews complaining about fit and more on to others because it fitas fine and works great and I would highly recommend this product. BTW one last though make sure you know your inside diameter of the hose you are reducing to this doesn't fit many shop vacs but fits my grizzly table saw's overhead dust collection hose (it has a 4" port under the blade and a 2.5" hose coming off the blade guard) and this is because many shop vacs are NOT 2.5". Just measure your hose or check your operators manual for specs and order the correct one as they do offer several different and even universal ones
Recommended Products
$104.99
$ 51 .99 $51.99
$120.00
$ 53 .99 $53.99