Your cart is empty.
Your cart is empty.Product Description
Wiegand Format:
- The standard 26-bit Wiegand format is an open format; it is a widely-used industry standard. Almost all access control systems accept the standard 26-bit format which consists of 2 parity bits, 8-bit facility code, and 16-bit card number fields. The Wiegand interface is commonly used to connect a card swipe mechanism to the rest of an access control system.
Features:
- The maximum reading distance is 2-23/64" (6cm).
- Waterproof, conforms to IP66.
- It is useful for safety door system, easy to connect and use.
- Ultra-low power consumption, the standby current is less than 50mA.
- Support wiegand 26bits or wiegand 34bits output format.
- Fast response speed, the door opening time is less than 0.3s.
- This device uses high performance MCU to ensure stable performance, and low-power circuit makes the service life longer.
- Widely used in factories, houses, residential quarters, offices, mechanical and electrical control equipment and so on.
- The RFID card reader can't work-alone and it needs to work with Wiegand protocol access controller, such as access control panel, fingerprint device or master controller.
Package:
- 1 x Card Reader
- 1 x User Manual
- 2 x Plastic Anchors
- 2 x #7 x 1" Self-Tapping Screw
Note:
- Frequency: 125Khz
- Card Type: EM-ID Card (Can't support HID, Cobra, APCiK etc.)
- Please notice that our wiegand reader can't be compatible with some encrypted cards, such as HID, Indala, Cobra, APCiK, Paradox, Radio, Honeywell, etc.
- Can't work alone, and it needs to work with access control panel. (Please search ASIN B00UX02JWE to get the access control panel.)
Installation:
- Remove the back cover from the reader
- Drill 2 holes on the wall for the self-tapping screws and 1 hole for the cable
- Put the supplied rubber plugs into the 2 holes
- Fix the back cover firmly on the wall with 2 self-tapping screws
- Thread the cable through the cable hole
- Attach the keypad to the back cover
Linford S.
September 5, 2025
A little bulky but works perfect with my L2/4 Controllers.
Shaun Martin
July 2, 2025
I tried to install this reader at my church. It will not even acknowledge 26-bit a fob being presented despite having the proper 12vdc voltage. No beep, no color change on the LED, nothing. That same fob works on other readers with no issues. The reader should acknowledge a fob or card being presented regardless of it being connected to an access control system. I have nearly 20 years as a technician in the electronic security industry and know access control systems.
Ralphie
May 26, 2025
Worked fine, but not with HID cards.
julienj
May 16, 2025
I bought this to test the interface with a Raspberry Pi and managed to get it working very reliably with little more than a pair of small signal diodes to block to the 5V signals from coming back to the Pi's GPIO. The device works very reliably.
Michael Phone
May 15, 2025
I ordered 6 of these and they would not recognize any cards. I am a low-voltage specialist.
Delfin Suarez
May 12, 2025
product work good, perfect what I need
GameMaker
April 19, 2025
The led and beep wires aren't functional. Also the firmware lights the green way too long after card scan. If its an invalid card I don't want the reader to turn green.
quantumorbit
February 14, 2025
Good quality. Works as expected.
Paolo
December 16, 2024
Il lettore si presenta incapsulatoPermette di essere resistente agli agenti atmosferici dotato di cicalinoOttimo a++
Recommended Products