Your cart is empty.
Your cart is empty.Product Description
Package list: 1 × Universal Joint, 2 × Screws
Compact structure:
The universal joint is flexible in all angles and has good coordination. The structure is compact and the clearance is small.
The universal joint is forged from high-quality carbon steel, and the steering is flexible and there will be no abnormal noise.
Surface fine grinding:
The whole universal joint is heat-treated to ensure its strength. Extend the service life of equipment and universal joints.
High torque:
The cross universal coupling can isolate or absorb axial vibration and impact, and has the characteristics of large torque, small transmission inertia, and large adjustment angle.
High transmission efficiency:
The universal joint coupling is a coupling that realizes the transmission of torque at a variable angle. It is used for the connection of mechanical parts that need to change the axis direction of the transmission shaft. It has a large angle compensation capability and high transmission efficiency.
Key accessories of universal joint:
After the middle square is turned by the machining center, it is finely ground on the grinder to make the pin and the square fit closely.
Use:
It has a wide range of applications and is suitable for various general machinery occasions.
Bob
2025-09-06 12:18:06
Works great
Laura Caley
2025-08-16 15:34:24
The ID is 12mm, (0.47in). When I asked to exchange it I was told by the manufacturer it was too expensive to send back and ask if I would accept a discount to keep it. I agreed because I had the tooling and set up to ream a blind hole and make it 0.5in. But beware I don't believe the manufacturer has 0.5in ID universal joints. And no I didn't want to turn the end of the shaft down.
S. Metzger
2025-08-03 13:51:42
I needed this for the snow shoot handle mechanism. I couldn’t find anything that worked locally. It took awhile to get here. It actually arrived the day after our big snowstorm. But I put it on, made a few adjustments on the handle rod and it worked great after the next storm. I was blowing snow for two hours and it worked great. This would have cost me about $200.00 if I would have taken it to a shop.
Joseph knight
2025-07-26 09:19:03
Item was exact fit had a timely delivery time very easy to assemble on my unit well done all around
Allen Holtzapfel
2025-06-20 09:33:18
The inside diameter is 12mm not 1/2". This product is mislabeled. (12mm = 0.472441 inches , close but will not easily connect two 1/2" metal shafts.)
M. Morrow
2025-06-17 15:10:11
Helps getting to the hard position places
dpeterson13
2025-05-20 15:38:40
This doesn't fit on a 1/2 inch shaft. It appears to be a metric size. I guess that because it came with no set screws and only metric set screws would fit. I'm disappointed that I wasted valuable time waiting for the wrong thing.
Customer
2025-05-15 13:12:23
The ID is not .5†and the set screws it comes with aren’t even the right size. They fall right through the threaded hole. The overall fit and finish is poor. It was hand assembled complete with complimentary Hammet marks. This is a $5 part sold for almost $18 at time of purchase. Stay away. Its garbage
Donzo
2025-04-13 17:48:52
Quality was great but item much smaller than expected so could not use!
Keith
2025-03-31 11:24:16
They slip on shaft because the grub screws supplied don't hold on shaft!!
Simon Rochette
2025-03-16 10:31:46
À l'air très fragile et les set screw ne sont même pas de la bonne grosseur..
Chill
2025-02-04 14:02:56
Very well manufactured, used as knuckle for gravity gimble for video rig
Han van Pelt
2025-01-29 17:58:18
It is advertised as 1/2" but a 1/2" rod will not fit. The actual diameter that does fit is 15/32". Disappointing but the metal is soft enough for me to drill it out to 1/2". Apart from that issue this item is well made.
Recommended Products